Supplying Power With The Battery - Panasonic NV-MX300B Operating Instructions Manual

Title

3) Supplying Power with the Battery

Before use, charge the Battery.
When charging, do not
connect the DC Input Lead
to the AC Adaptor.
10
AC Adaptor
[QUICK] Lamp [100%] Lamp
Procedure
1 2
Place the Battery on the Connect the AC Mains
AC Adaptor and slide it Lead to the AC Adaptor
horizontally until it and to an AC mains
stops. socket.
After the [POWER] Lamp
has lighted, the
[CHARGE] Lamp flashes.
≥The AC Mains Lead
does not fit entirely into
the AC Adaptor socket,
however this has no
effect on operation.
4 5
Remove the Battery by Slide the Viewfinder
sliding it in the opposite backward to its fully
direction of Step 1 . extended position and
≥Also disconnect the AC then tilt it upward.
Mains Lead.
Charging Time and Maximum Time for Continuous Recording
Battery No. A B
CGP-D210 1 h 30 min. 1 h 45 min. (1 h 30 min.)
VSB0419
/
(supplied)
CGR-D220 1 h 10 min. 2 h 5 min. (1 h 50 min.)
CGP-D320 2 h. 3 h 45 min. (3 h 20 min.)
CGR-D815 4 h 30 min. 7 h. (6 h 5 min.)
A Charging Time
B Maximum Continuous Recording Time
C Intermittent Recording Time (The Intermittent Recording Time indicates the total recording time
possible when you start and stop recording repeatedly.)
D Time Before [QUICK] Lamp Stops Flashing (Quick Charge)
E Maximum Continuous Recording Time When [QUICK] Lamp Is Lit
(The times shown in the above chart are approximations. The figures in parentheses show the
recording time when using the LCD Monitor.)
The times listed above for your information indicate the duration of recording performed at an ambient
temperature of 20eC and 60% relative humidity. The charging time may be longer when you charge the
Battery at higher or lower temperature.
3
When the [100%] Lamp on the AC Adaptor is lit,
charging is finished.
≥When the [QUICK] Lamp is lit, approximately
45 minutes of continuous recording is possible.
≥The [QUICK] Lamp flashes and then remains lit only
when charging a quick-charge type battery.
≥Charging is not possible when the DC Input Lead is
connected to the AC Adaptor.
≥It may take some moments for the [POWER] Lamp
or [CHARGE] Lamps to flash or light up: this is
normal and not a malfunction.
POWER CHARGE
QUICK 100%
6
Insert the Battery into the Battery Holder on the
Movie Camera and slide it downward until it locks
with a click.
C D E
55 min. (45 min.) 20 min. 45 min.
1 h 5 min. (55 min.) 15 min. 45 min.
1 h 55 min. (1 h 40 min.) 15 min. 45 min.
3 h 30 min. (3 h 5 min.)
s s
Remarks, etc.
≥During use and charging, the Battery becomes warm.
The Movie Camera, too, becomes warm during use.
≥When you repeatedly stop and restart recording, the
recording time per Battery is shorter than listed above.
≥If you do not use the Battery for a long time, please
read "Precautions for Storage". (p. 110)
Quick Charge
When you attach a quick-charge type battery to the AC
Adaptor, the [QUICK] Lamp starts to flash. When the
[QUICK] Lamp has stopped flashing and remains lit,
approximately 45 minutes of continuous recording is
possible.
≥The Battery model CGR-D815 (optional) is not quick-
charge type battery.
≥If you use the Car Adaptor Cord (optional) (p. 8) to
charge the Battery, quick-charging is not possible.
When the Charge Lamps Flash alternately as
Warning
If the ambient temperature is extremely low or high, the
Charge Lamps (the [100%] Lamp and the [QUICK] Lamp)
on the AC Adaptor flash alternately. They also flash when
some malfunction has occurred in the Battery or the AC
Adaptor. For details, read "When the Charge Lamps on the
AC Adaptor Flash as Warning". (p.109)
Removing the Battery from the Movie Camera
While pressing the [BATTERY EJECT] Button, slide
the Battery upward to remove it.
≥Be careful not to drop the Battery by accident.
≥Before removing the Battery, set the [OFF/ON/MODE]
Switch to [OFF].
[BATTERY EJECT]
BATTERY
EJECT
Button
PUSH
11