Panasonic NV-MD9000EN Operating Instructions Manual page 32

Wipe Mode and Mix Mode
If either one of the following operations is
carried out, stored images will be erased, and
Wipe and Mix Functions cannot be used.
≥Use the Camera Search Function
≥Press the [STILL] Button
ª Adjusting the Microphone Sensitivity
Lebel
≥When this setting is changed, the [AUDIO
LEVEL] setting on the [RECORDING SETUP]
Sub-Menu of the [VCR FUNCTIONS]
Main-Menu will likewise be changed.
≥When [ZOOM MIC] is set to [ON], set the
zoom to the [T] position before performing this
adjustment.
≥Select a lower setting for [GAIN] or set [MIC
LEVEL] to [AUTO].
≥It is recommended that you check through the
headphones before recording to ensure that
the sound is not distorted.
ª Playing Back
Repeat Playback
If you continue to press the [1] Button for
5 seconds or longer, the Movie Camera
switches to Repeat Playback Mode, and the
[R !] Indication appears. (To cancel Repeat
Playback Mode, set the [OFF/ON] Switch to
[OFF].)
Listening to Playback Sound through
Headphones
If you want to use the headphones to listen to
the playback sound, connect the headphones to
the [PHONES] Socket (
-39-
Camera. In this case, no sound (including a
warning sound and shutter sound) will be
reproduced through the built-in speaker of the
Movie Camera.
Choosing Sound during Playback
You can select the sound by using the
[AUDIO OUT] setting on the
[PLAYBACK FUNCTIONS] Sub-Menu.
STEREO: Stereo Sound (main sound and
sub sound)
L: Left channel sound (main
sound)
R: Right channel sound (sub
sound)
≥If you dub a tape recorded at the [12bit]
selected as the [AUDIO REC] on the
[RECORDING SETUP] Sub-Menu, playback
sound becomes stereo sound regardless of
the [AUDIO OUT] setting if [12bit AUDIO] is
set to [MIX].
ª Index Search Functions
≥Index Search may not be possible at the
beginning of tape.
≥Because Photoshot Index Signals are not
recorded on still pictures recorded in
Continuous Photoshot Mode, the Photoshot
Index Search Function cannot be used for
these still pictures.
≥Scene Index Search may not function properly
if the interval between 2 scene index signals is
shorter than 1 minute.
ª Playback Zoom Function
≥You cannot adjust the sound volume with the
Remote Controller in Playback Zoom Mode.
Others
) on the Movie
-66-
≥If you turn off the Movie Camera power or if
you switch from VCR Mode to Camera Mode,
Playback Zoom Mode is automatically
cancelled.
≥Even if Playback Zoom Functions are being
used, images that are output from the DV
Terminal ( ) are not enlarged.
-39-
≥As you enlarge an image, the quality of image
suffers.
≥During a Playback Zoom, the Variable Speed
Search Function cannot be changed with the
Remote Controller.
ª
Playback Digital Effect Functions
≥Signals of images to which digital effects are
added during playback cannot be output from
the DV Terminal ( ).
-39-
≥You cannot use the Wipe or Mix Function
while playing back the non-recorded portion of
tape.
ª
Playing Back on Your TV
≥If you set [AV JACK] on the [AV IN/
OUT SETUP] Sub-Menu to [IN/OUT], nothing
will be shown on the TV screen except during
playback.
≥If you connect the AV Cable to the [AUDIO IN/
OUT] Sockets only, the sound cannot be
output from the Movie Camera. Connect the
AV cable to the [VIDEO IN/OUT] socket too.
ª
Audio Dubbing
≥The blank section of a tape cannot be dubbed.
≥Sounds sent through the DV Terminal cannot
be dubbed.
≥If a tape has a non-recorded portion when the
tape is dubbed, images and sounds may be
disturbed when this portion of the tape is
played back.
≥If you set the tape counter back to 0 at the
position where you want to stop Audio
Dubbing so as to make it possible to use the
Memory Stop Function (
-72-
terminated automatically when the tape
reaches this position.
≥In the case of importing data recorded with
Audio Dubbing to a PC using the PC's
software programme, only the original sound
(ST1) may be imported, depending on the
software programme.
ª
Recording the Contents of Other
Equipment
Analog-Digital Conversion
≥When the Movie Camera is connected with
other digital video equipment through its DV
Terminal, images recorded in analog form
from other external equipment can be output
to the digital video equipment through the DV
Terminal.
≥To DV-output analog video signals sent from
other equipment, set [DV OUT] on the [AV IN/
OUT SETUP] Sub-Menu to [ON]. (Normally,
keep the [DV OUT] set to [OFF]. If it is set to
[ON], the quality of the image may be
disturbed.)
), Audio Dubbing is