18 volt cordless 3/8" drill & flashlight kit (16 pages)
Summary of Contents for Drill Master 91176
Page 1
2004 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. SKU 91176 PRODUCT SPECIFICATIONS 1/2” - Keyless Chuck 0-500 RPM (low), 0-1600 RPM (high) 7 (from 4.4 to 70.7 in.-Lbs.)
Page 3
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 91176 ELECTRICAL SAFETY PERSONAL SAFETY...
Page 4
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. SKU 91176 TOOL USE AND CARE PAGE 4...
Page 5
Maintain labels and nameplates on the Hammer Drill. These carry impor- tant information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Always wear safety impact eye goggles and heavy work gloves when using the Hammer Drill.
Page 6
(GFCI) system is also a good precaution. This inexpensive device is a good safety measure because it prevents a sustained electrical shock. - Properly maintain and inspect all tools before use to avoid electrical shock. SKU 91176 PAGE 6...
Page 7
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A SKU 91176 GROUNDING WARNING! PAGE 7...
(See Figure C.) If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) SKU 91176 EXTENSION CORDS PAGE 8...
Page 9
3.5 - 5.0 5.1 - 7.0 7.1 - 12.0 12.1 - 16.0 16.1 - 20.0 FIGURE C SKU 91176 (120 VOLT) EXTENSION CORD LENGTH 50 FEET 75 FEET *Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
When unpacking, check to make sure all the parts shown on the Parts List on page 14 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
Chuck (1) and close the Jaws. Make sure the bit is securely held in the Jaws of the Chuck (1) by putting on a thick work glove and pulling on the bit. SKU 91176 FIGURE 4 Torque Settings...
Trigger (16) after you are sure the bit is securely in the pilot hole. After complet- ing the task, stop the Hammer Drill, reverse the direction of the drill (see number 6 above), and gently squeeze the Trigger (6) as you back out the drill. SKU 91176 Torque Indicator Arrow Variable Speed Switch (5)
Page 13
4. Check that the Jaws of the Chuck (1) are clear of any dirt, debris, or grease. 5. Check bits carefully. Never use a cracked or bent bit. New bits are available at Harbor Freight Tools. 6. Properly recycle or dispose of Ni-Cd battery when it no longer recharges. Do not throw the battery in a fire.
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 91176 PARTS LIST Part No. Description...
ASSEMBLY DIAGRAM The AC/DC Adapter and Charger Base (20) is not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91176 PAGE 15...