Specifications - Pioneer M-AX10 Operating Instruction

SPECIFICATIONS

Amplifier Section
(U.S. model only)
When set to Bridge mode:
continuous average power output is 200
Watts* per channel, min., at 6 ohms from 20
Hertz to 20,000 Hertz with no more than
0.2%** total harmonic distortion.
When set to Dual, Separate mode:
Continuous average power output is 90
Watts* per channel, min., at 3 ohms from
20 Hertz to 20,000 Hertz with no more
than 0.2%** total harmonic distortion
Continuous power output
(driven simultaneously at 20Hz to 20kHz)**
(European model only)
Bridge mode
W . . . . . . . . . . . . . . . . .220W X 2
T.H.D. 0.15% 6
T.H.D. 0.09% 8 W . . . . . . . . . . . . . . . . .190W X 2
Dual, Separate mode
T.H.D. 0.15% 3 W . . . . . . . . . . . . . . . . .100W X 4
T.H.D. 0.09% 4 W . . . . . . . . . . . . . . . . .90W X 4
T.H.D. 0.08% 8 W . . . . . . . . . . . . . . . . .60W X 4
DIN Continuous power output
(driven simultaneously at 1kHz)
(Euopean model only)
Bridge mode
T.H.D. 1% 6 W . . . . . . . . . . . . . . . . . . .230W X 2
T.H.D. 1% 8 W . . . . . . . . . . . . . . . . . . .200W X 2
Dual, Separate mode
T.H.D. 1% 3 W . . . . . . . . . . . . . . . . . . .110W X 4
T.H.D. 1% 4 W . . . . . . . . . . . . . . . . . . .105W X 4
T.H.D. 1% 8 W . . . . . . . . . . . . . . . . . . . .65W X 4
Total harmonic distortion**
Bridge mode
20 Hz to 20kHz, 100W, 8 W . . . . . . . . . . .0.08%
Dual, Separate mode
20 Hz to 20kHz, 30W, 8 W . . . . . . . . . . . .0.06%
Input sensitivity/Impedance
INPUT1,2 . . . . . . . . . . . . . . . . . . . . . . . .1V/47kW
Frequency Response
INPUT1,2 . . . . . . . . . .5Hz to 150kHz +0dB,-3dB
Dumping factor (1kHz/20Hz to 20kHz)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .400/300
Signal-to Noise ratio (IHF short circuit, A
network ATT THROUGH ON)
INPUT 1,2 . . . . . . . . . . . . . . . . . . . . . . . . .125dB
Channel separation(20Hz to 20kHz)
Bridge mode . . . . . . . . . . . . . . . . . . . . . . .104dB
Dual, Separate mode . . . . . . . . . . . . . . . .115dB
Power supply/Miscellaneous
Power requirements
U.S. model . . . . . . . . . . . . . . . . . .AC 120V 60Hz
European model . . . . . . . . . . .AC 230V 50/60Hz
Power consumption
U.S. model . . . . . . . . . . . . . . . . . . . . . . . . .370W
European model . . . . . . . . . . . . . . . . . . . .400W
Dimensions . . . . . .440(W) x 420(D) x 178(H)mm
17
Weight (without package) . . .25.8Kg(56lb 14oz)
Accessories
Operating instructions . . . . . . . . . . . . . . . . . . .1
NOTE
Specifications and design subject to possible
modification without notice, due to
improvement.
* Measured pursuant to the Federal Trade
Commission's Trade Regulation rule on Power
Claims for Amplifier.
**Measured by Audio Spectrum Analyzer.
5 / (W) x 16 1 / (D) x 7(H) in
16 2
17
17