Table of Contents
Advertisement
FAQs
Problem
No sound is produced
Sound level is low
or sound is distorted
Sound is unusual
Pictures from external equipment
are unusual when the equipment
is connected via HDMI
"Control with HDMI"
function does not work
The SD card cannot be used
even when it is formatted
TV unit goes into
"Standby mode"
The remote control
does not work
On screen messages
Problem
On screen messages
All tuning data will be erased
Are you sure ?
DOWNLOAD IN PROGRESS PLEASE WAIT
Feature not available
Incorrect PIN Number
Key not available
No recording -Check Tape or Disc
No recording - UNKNOWN REASON
Please check settings and connections on
HDMI devices.
No stations found
Please insert the aerial
Please wait.
Recording in progress
Recording stopped - TV source changed
Unable to download, Check Equipment
WARNING
All current tuning data will be erased
40
Actions
•
Is "Sound Mute" active? (p. 7)
•
Is the volume set to the minimum?
•
Sound signal reception may be deteriorated.
•
Set "NICAM" (p. 19) in the Sound menu to "Off".
•
Set the sound setting of the connected equipment to "2ch L.PCM".
•
Check the "HDMI1 input" setting in the Sound menu. (p. 19)
•
If digital sound connection has a problem, select
analogue sound connection. (p. 19)
•
Is the HDMI cable connected properly? (p. 34)
•
Turn Off the TV unit and equipment, then turn them On again.
•
Check an input signal from the equipment. (p. 37)
•
Use an equipment compliant with EIA/CEA-861/861B.
•
Switch the TV unit on again with the equipment on.
•
Set "Control with HDMI" to "Off", then set to "On" again. (p. 32)
•
Contact the authorized Service Centre.
•
The sleep function is activated.
•
The TV unit enters "Standby mode" about 30 min. after broadcasting ends.
•
Are the batteries installed correctly? (p. 6)
•
Has the TV unit been switched On?
Actions
Actions / Meanings
•
"Shipping condition" will erase all tuning data.
•
Make sure the operation is with your desire.
•
Q-Link channel download is in progress.
•
•
Check the Q-Link connection and setting (p. 30).
The impossible source (Component / HDMI / PC) to be record.
•
The PIN number you entered is wrong.
•
You cannot select the same input source between Main and
Sub screen when you are viewing in multi window. (p. 13)
•
The tape or disc may be "write protected", missing or damaged.
The equipment may already be recording.
•
•
The recording cannot be done by any reason. Check the equipment.
Disc or tape may be full.
•
Communication error in Control with HDMI function (p. 32).
•
No signal can be found in Auto setup.
•
A function is in progress.
•
The recording equipment is recording the programme signal from
its own tuner. You can turn the TV off and leave the equipment
recording in the normal way.
•
Direct TV recording will stop if channel or input source is changed.
•
The tape or disc is active. Stop the equipment and try again.
•
Auto setup will be erased all present tuning data (p. 23).
On screen messages (SD Card)
On screen messages
•
Is SD Card in?
Insert a SD card.
•
SD Card is locked
Unlock the SD card.
Please unlock to operate
•
This fi le is locked
Unlock the fi le in the card.
Please unlock to operate
•
This type of format is not
The unit does not support the format.
supported
(For the applicable formats and data, see p. 38.)
•
This type of card is not
A card not supported by the unit has been inserted.
supported
(For the supported cards, see p. 38.)
•
Broken fi le
The fi le is broken.
Cannot display image
•
Memory full
The card memory is full.
•
Not enough memory
The card does not have enough memory to operate.
•
Cannot read fi le
The fi le is not readable.
•
Unrecordable source
That channel cannot be recorded. (Recording is automatically
SD recording is stopped
stopped.)
•
Error
Re-insert the card. If the error persists, format
Check card
the card. (p. 29)
•
Card recording in progress
That operation is not available during recording.
Please stop recording to operate
To continue the operation, stop recording.
(For example, changing channels while recording)
•
Delete fi le?
Displayed when you press Red colour button to delete a
MPEG4 fi le. Press OK button to confi rm deleting.
Cautions when handling SD Card :
•
Do not remove the card while the unit is accessing data ("blue" LED
On) (this can damage card or unit).
•
Do not touch the pins on the back of the card.
•
Do not subject the card to a high pressure or impact.
•
Insert the card in the correct direction (otherwise, card may be
damaged).
•
Electrical interference, static electricity, or erroneous operation may
damage the data or card.
•
Back up the recorded data at regular intervals in case of deteriorated
or damaged data or erratic operation of the unit. (Panasonic is not
liable for any deterioration or damage of recorded data.)
Actions / Meanings
Blue LED
WARNING: As with an small object, SD
card can be swallowed by young
children. Do not allow children to handle
SD card. Please remove SD card
immediately after use.
41
Advertisement
Table of Contents
