Table of Contents
Advertisement
How to Use Menu Functions
■
Menu list
Item
Menu
Selects which AV terminal is to be used for data communication between this TV and a
Q-Link
compatible recording equipment (AV2 / AV3) (p. 30)
Chooses the signal to be transmitted from the TV to Q-Link (TV / AV1 / AV2 / AV3 /
•
AV4 / Monitor)
AV2/AV3 out
Monitor: Image displayed on screen
•
Component, PC and HDMI signals cannot be outputted
Control with HDMI
Control with HDMI function (Off / On) (p. 32)
Teletext
Teletext display mode (FASTEXT / List) (p. 14)
Off timer
Sets the time the unit automatically turns Off. (Off / 15 / 30 / 45 / 60 / 75 / 90) (minutes)
Volume correction
Adjusts volume for AV, PC, HDMI and component mode
Increases the brightness of the side panel (Off / Low / Mid / High)
•
Side panel
The recommended setting is "High" to prevent panel "after-image"
Power save
Reduces brightness of picture to economise on power consumption (Off / On)
Set to "TV" to view picture from TV tuner.
Set to "AV" to view input from an external equipment connected to a SCART terminal,
e.g. satellite receiver
Power on preference
(TV / AV)
•
The external equipment must be switched on and sending a control signal for
automatic switching at power on to occur
Programme edit
Edits channels (p. 23)
Auto setup
Sets channels automatically (p. 23)
Manual tuning
Sets channels manually (p. 23)
Fine tuning
Fine tuning of channels (during rain, etc.)
Owner ID
Inputs the owner ID (p. 25)
Shipping condition
Resets all settings, for example, when moving house (p. 24)
•
A different menu will be displayed while PC or SD Card is used.
•
In AV mode, the Setup menu gives a reduced number of options.
20
Adjustments / Confi gurations (alternatives)
(p. 21 and p. 27)
Displaying PC Screen on TV
The screen of the PC connected to the unit can be displayed on the TV.
You can also listen to PC sound with the audio cable connected. To connect PC (p. 34)
Select the external input
1
2
Select "PC"
yellow
(Press twice)
■
To return to TV
■
PC menu setting (changed as desired)
•
To make settings
"How to Use Menu Functions"
Menu
Item
Adjustments / Confi gurations (options)
Viewing mode, Contrast, Brightness, Sharpness, Colour balance (p. 19)
W/B High R
White balance of bright red area
W/B High B
White balance of bright blue area
Advanced
W/B Low R
White balance of dark red area
setting
W/B Low B
White balance of dark blue area
Gamma
(2.0 / 2.2 / 2.5 / S Curve)
Switches to a wide view
•
Input
VGA (640 x 480 dots), WVGA (852 x 480 dots),
resolution
XGA (1,024 x 768 dots), WXGA (1,366 x 768 dots)
•
Options change depending on signals
Clock
Set to the minimum level if noise occurs
Adjusts horizontal position
H-pos
PC
Adjusts vertical position
setup
V-pos
Eliminates fl icker and distortion
•
Clock phase
Adjust after Clock adjustment
Chooses another synchronous signal if the image is distorted (H&V / On G)
•
Sync
H&V : by the horizontal and vertical signals from your PC
On G : by the green signal from your PC (if available)
Volume correction, Side panel, Power save (p. 20)
•
Sound menu (p. 19)
To
next
page
blue
HDMI1/2
•
Corresponding signals
(p. 37)
•
If "H-freq." or "V-freq."
is shown in red, the
signals may not be
supported.
Displays PC screen
to
(p. 18)
and
repeatedly adjusted
•
Set to the minimum level if noise occurs
21
Advertisement
Table of Contents
