Supplied accessories
AC adaptor (for multi cradle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DE-935DA
Pair of stereo earphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L0BAB0000172
Multi cradle
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RFE0116A
USB cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .K1HA12BD0001
External microphone (monaural) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .L0FBBA000002
CD-ROM (Voice Editor 3)
Nickel-metal hydride rechargeable battery (Recommended replacement: HHR-4AH)
≥Use numbers indicated when asking for replacement parts.
To order accessories contact 1-800-332-5368 or web site (http://www.panasonic.com).
Power supply
Rechargeable battery
1
Insert the battery.
2
Recharge.
Start:
Finish:
DC IN jack
Household
AC outlet
AC adaptor
THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
≥You can use the unit while the battery is recharging.
Recharge while the unit is stopped (page 6-7) to fully recharge.
≥You can recharge Panasonic rechargeable battery even if it is only partially drained.
≥Disconnect the AC adaptor to save power if you are not going to use the unit for a
long time. The unit consumes approximately 0.3 W, even when it is turned off.
Dry cell battery (not included)
Use a long life "AAA, LR03, AM-4" alkaline battery.
≥Insert the same way as the rechargeable battery.
Multi cradle and AC adaptor
Insert either a rechargeable or dry cell battery.
≥The multi cradle works on AC and the main unit works on the battery.
When using a rechargeable battery, it is recharged as you use the unit so you can
use it over a longer time.
When using a dry cell battery, you can use the unit until the battery goes flat.
AC adaptor
This AC adaptor operates on AC between 100 V and 240 V.
But
≥In the U.S.A. and Canada, the AC power supply cord must be connected to a
120 V AC power supply only.
≥When connecting to an AC supply outside of the U.S.A. or Canada, use a plug
adaptor to suit the AC outlet configuration.
≥When connecting to a supply of greater than AC 125 V, ensure the cord you use
is suited to the voltage of the AC supply and the rated current of the AC adaptor.
≥Contact an electrical parts distributor for assistance in selecting a suitable AC
plug adaptor or AC cord set.
The battery indicator (displayed during operation)
FULL
If you operate the unit in the cradle
while a dry cell battery is inserted,
the whole indicator flashes.
Recharge before first use.
1
2
"CHARGE" lights
;
"CHARGE" goes out
(approx. 2.5 hours)
Insert so
"CHARGE"
lights.
Replace the battery
EMPTY
when the indicator
flashes.
Change the battery
within 20 seconds to
preserve memory
items.
2
Hold function
This causes the unit to ignore accidental button presses.
You cannot operate the multi cradle if hold is on.
Hold mode
∫
To save the batteries
While stopped, switch to hold so the display turns off.
Setting the time
The year (2003) starts flashing on the display after you insert a battery.
(See "Correcting the time settings" below if it doesn't.)
Repeat the SELECT ) SET steps to set the clock.
The clock has a monthly accuracy of i/j 60 seconds at room temperature.
[ $ FOLDER/
1
SELECT
% MENU]
Year
Month
Day
M
D
M
D
Correcting the time settings
1. While stopped, press and hold [ $ FOLDER/ % MENU] until "HQ SP LP" appears.
Do each of the following within 10 seconds
2. Press [:,9] until "yEAr" appears.
3. Press [1/∫].
4. Follow the above steps to change the setting you want to correct.
≥Start from the beginning again if the display returns to the clock partway through.
≥Press [ $ FOLDER/ % MENU] for two seconds to stop partway through.
Turning the operation beep on and off
[ $ FOLDER/
% MENU]
≥Start from the beginning again if the display returns to the clock partway through.
≥Press [ $ FOLDER/ % MENU] for two seconds to stop partway through.
Lights for about
Release
two seconds
2
SET
Within 10 seconds
12 or 24 hour
Time
Clock
HQ
A
AM
AM
Starts flashing
when finished
1 While stopped, press and
hold [ $ FOLDER/ % MENU]
until "HQ SP LP" appears.
Do each of the following
within 10 seconds
2 Press [:,9] until
"bEEP" appears.
3 Press [1/∫].
4 Press [:,9] to select
"bE On" or "bE OFF".
5 Press [1/∫].
3