FAQs
Problem
Problem
No sound is produced
Sound level is low
or sound is distorted
•
Due to the digital reception technologies involved, quality of the DTV signals may be relatively low in
some cases, despite good reception of analogue programmes.
Unable to receive
signals with a
high-performance
aerial
Sound is unusual
An error message
appears
"Control with HDMI"
function does not work
TV unit goes into
"Standby mode"
An error message
appears
38
Actions
Actions
•
•
Is "Sound Mute" active? (p. 7)
Is the volume set to the minimum?
•
•
Sound signal reception may be deteriorated.
Set "MPX" (p. 16) in the Sound menu to "Mono".
(Analogue only)
•
Install an aerial individually for the TV unit and VCR
(or use a splitter).
TV
(Individual aerial)
Splitter
Aerial Output
Aerial
Input
Aerial Input
Aerial Output
terminal
VCR
(Individual aerial)
•
Set the sound setting of the connected equipment
•
to "2ch L.PCM".
Check the "HDMI input" setting in the Sound menu.
•
(p. 16)
If digital sound connection has a problem, select
analogue sound connection. (p. 34)
•
Contact the authorized Service Centre.
•
•
Switch the TV unit on again with the equipment on.
Set "Control with HDMI" to "Off", then set to "On" again.
(p. 27)
•
•
The sleep function is activated.
The TV unit enters "Standby mode" about 30 min.
after broadcasting ends.
•
•
Follow the message's instructions.
If the problem persists, contact the authorized
Service Centre.
Licence
Trademark Credits
•
•
DVB is a trademark of the DVB Digital Video Broadcasting Project (1991 to 1996).
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
TH-37PD60E Declaration of Conformity No 3974, 19th January 2006
TH-42PD60E Declaration of Conformity No 3973, 19th January 2006
Specifications
TH-37PD60E
Power Source
AC 220-240 V, 50 / 60 Hz
Average use
215 W
0.3 W (Without Tuner Lock On)
Standby condition
20 W (With Tuner Lock On)
Drive method
AC type
Aspect Ratio
16:9
Contrast Ratio
Max 10000:1
94 cmV
Visible screen size
818 mm (W) × 461 mm (H) ×
(No. of pixels)
939 mm (diagonal)
408,960 (852 (W) × 480 (H)) [2,556 × 480 dots]
12 cm × 6 cm × 2 pcs, 8 Ω
Speaker
Audio Output
20 W (10 W + 10 W), 10% THD
PAL B, G, SECAM B, G, SECAM L / L'
VHF E2 - E12
CATV (S01 - S05)
CATV S11 - S20 (U1 - U10)
Receiving Systems /
PAL 525/60
: Playback of NTSC tape from some PAL Video recorders (VCR).
Band name
DVB
: Digital terrestrial services via VHF / UHF aerial input.
M.NTSC
: Playback from M.NTSC Video recorders (VCR).
•
NTSC (AV input only) : Playback from NTSC Video recorders (VCR).
TV signals may not be received in some areas.
Aerial - Rear
VHF / UHF
Temperature : 0 °C - 40 °C
Operating Conditions
Humidity
: 20 % - 80 % RH (non-condensing)
AV1 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in)
AV2 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, S-Video in, Q-Link)
AV3 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
Y
COMPONENT
P
, P
B
R
Others
HDMI
TYPE A Connector
AUDIO L - R
RCA PIN Type × 2
Output AUDIO L - R
RCA PIN Type × 2
968 mm × 641 mm × 97 mm (TV Set only)
Dimensions ( W × H × D )
968 mm × 704 mm × 320 mm (With Pedestal)
25.0 k Net (TV Set only)
Weight
27.0 k Net (With Pedestal)
Note
•
•
Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020.
TH-42PD60E
247 W
106 cmV
920 mm (W) × 518 mm (H) ×
1,056 mm (diagonal)
UHF E21 - E69
CATV S1 - S10 (M1 - M10)
CATV S21 - S41 (Hyperband)
1.0 V[p-p] (including synchronization)
±0.35 V[p-p]
0.5 V[rms]
0.5 V[rms] (high impedance)
1,068 mm × 701 mm × 97 mm (TV Set only)
1,068 mm × 764 mm × 320 mm (With Pedestal)
29.0 k Net (TV Set only)
31.0 k Net (With Pedestal)
39