Table of Contents
Advertisement
Available languages
Available languages
Multi-Brand Control Feature
Advanced Connections
Multi-Brand Control Setup
Audio/Video connection
The Remote Control can be set to control some TV functions.
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR
to them to receive higher quality picture and sound.
1
Find your TV Brand Code Number from those shown below.
2
Set up for TV control,
➛ hold down TV button,
➛ enter code with NUMBER keys.
3
Confirm code entry,
➛ press POWER to turn your TV on or off.
• See table below for controllable functions in each mode.
Notes
• Repeat setup after remote battery replacement.
• Remote will not control every TV made by the manufacturer listed. If you get no
response, your particular unit cannot be controlled. There are NO additional codes for
the products listed. If your product is not listed, then the remote is not compatible with
that product.
Using Multi-Brand Control
1
After remote is set up, you can select VCR or TV for the desired function.
Connect the VCR's VIDEO OUT jack to the TV's VIDEO IN jack.
Press VCR or TV on the remote.
(Table below shows available unit buttons for each mode.)
Unit
2
VCR
TV
Connect VCR's L/R AUDIO OUT jacks to the TV's L/R AUDIO IN jacks.
Mode
VCR
All
VOL UP/DOWN
VCR/TV, PLAY, STOP, EJECT, DISPLAY, FF, REW,
POWER, INPUT, ENTER,
TV
PAUSE/SLOW, REC, SAP/Hi-Fi, SPEED, CM/ZERO,
NUMBER keys, CH UP/
3
RESET COUNTER, TAPE POSITION
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to "VIDEO."
DOWN, VOL UP/DOWN
Notes
• Not all functions listed may be controllable.
• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for
channel selection.
I I I I I With a Cable Box (VCR
TV Brand Code Numbers
ANT
AUDIO
or
Panasonic ........................ 01, 02
Sylvania ................................. 05
JVC ........................................ 11
Quasar ............................. 01, 02
Sharp ............................... 06, 07
Hitachi ................................... 12
CATV
VIDEO
RCA ....................................... 03
Sony ...................................... 08
Mitsubishi ........................ 07, 13
GE ......................................... 03
Toshiba .................................. 09
Samsung ............................... 14
IN 1
OUT
Zenith .................................... 04
Sanyo .................................... 10
Gold Star ................... 15, 16, 17
Magnavox .............................. 05
Fisher .................................... 10
Important Notes
• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one
listed.
I I I I I Connect With Two Cable Boxes
• Some TV brands require you to turn on the power manually.
CABLE BOX
IN
OUT
ANT
or
2-Way Splitter
CATV
OUT 1
OUT 2
- 2 -
PV-453-K Ad-2 (E) (030206).p65
3
PV-453-K(E) LSQT0649A REAR
MTS Broadcast
Connection
Make the Audio/Video Connection as shown on page 3.
• You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
IN FROM ANT.
VCR
TV
R
AUDIO OUT
L
R
R
AUDIO IN
L
R
VHF/UHF
OUT TO TV
L
VIDEO OUT
VHF/UHF
VIDEO IN
Receivable Broadcast Types
The following are possible audio broadcast types and on-screen displays.
The signal being received is indicated with an " " mark while the selected audio mode is
indicated with an arrow.
To display the broadcast signal being received,
➛ ➛ ➛ ➛ ➛ press DISPLAY*.
MTS Stereo and SAP broadcast
Multi-channel Television Sound Stereo (main language)
and Secondary Audio Program (sub language)
broadcasts are being received simultaneously.
Select STEREO or SAP audio mode.
Cable Box)
You Can
You Cannot
MTS Stereo broadcast
TV
• view any
• record
Multi-channel Television Sound Stereo broadcast.
scrambled
(including
IN FROM ANT.
Select STEREO audio mode.
IN
OUT
channels.
R
scrambled)
R
• If stereo broadcast is weak and display flickers,
CABLE BOX
channel.
AUDIO
L
L
select MONO audio mode for possible better results.
VHF/UHF
OUT TO TV
IN
OUT
VIDEO
• use VCR
VHF/UHF
Remote
Control to
VCR
select
channels
SAP broadcast
without using
Secondary Audio Program (sub language) broadcast.
Multi-brand
Select SAP audio mode for the sub language.
control feature.
You Can
You Cannot
VCR
• record and
• view a
channel
view both
AUDIO
IN FROM ANT.
other than
scrambled and
MONO broadcast
R
unscrambled
the one
Normal monaural sound broadcast.
L
VHF/UHF
selected for
channels if
VIDEO
OUT TO TV
any type of
additional
TV
equipment is
recording.
IN 1
OUT
added. This
IN
OUT
• do a Timer
A/B Switch
connection
R
CABLE BOX
requires: two
recording of
AUDIO
L
a channel
converter
IN
OUT
IN 1
IN 2
VIDEO
boxes, an A/B
unless you
VHF/UHF
switch, and a
select it at
the cable
2-way splitter.
box.
Equipped with
®
-TV Noise Reduction for true
MTS reproduction.
®
-TV Noise Reduction is
required for good stereo separation and audio
fidelity.
®
is a registered trademark, and is
licensed by
®
Technology Licensing.
- 3 -
VHS Hi-Fi Stereo System
Audio Mode for Recording
1
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
2
Press SAP/ Hi-Fi repeatedly
to select desired mode.
STEREO
SAP
• Refer to "Receivable
MONO
VCR
Broadcast Types" on page 4.
Stereo Amplifier
AUDIO OUT
R
• Arrow indicates selection.
R
L
3
AUDIO IN
Make a recording.
R
See p. 5 of "Basic Operations" Instruction book.
L
OUT TO TV
Audio Mode for Playback
1
Start playback.
See p. 5 of "Basic Operations" Instruction book.
2
Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
3
Press SAP/ Hi-Fi repeatedly
STOP
1 2 : 0 0AM
CH 02
to select desired mode.
0 : 0 0 : 0 0
H I F I : L / R
STEREO
SP
H I F I : L
SAP
H I F I : R
• Select "HIFI(L/R)" or
NORMAL
MONO
"HIFI(L)" or "HIFI(R)" to
listen to stereo recordings in
stereo sound.
Select "NORMAL" for
• Arrow indicates
monaural sound.
selection.
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SP
SAP
MONO
Notes
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.
Standard stereo tapes will playback in monaural sound.
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
• To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to
STEREO
SP
SAP
a stereo TV or an external stereo amp and speakers. (See page 4.)
MONO
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
STOP
1 2 : 0 0AM
CH 02
0 : 0 0 : 0 0
STEREO
SP
SAP
MONO
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
- 4 -
- 5 -
2003/02/13, 11:04
Tape Operation
Tape Operation
Search System
Repeat Play
For each recording, an invisible index mark is placed on the tape. A program index and
Set to playback a recording over and over.
information are also included for timer recordings. These marks are used to access or
scan recordings.
1
Press ACTION to display menu.
Index Search
Program End Search
2
VCR
CLOCK
CHANNEL
REPEAT PLAY
:OFF
REMOTE WARNING
:ON
Locates end point of recording for continuity.
AUTO SHUT- OFF
:OFF
1
SEARCH
Press SEARCH* to
AUTO VCR/TV
:ON
INDEX
PROGRAM END
display SEARCH in Stop
IDIOMA/LANGUE : ENGLISH
VCR' S OUTPUT CH
:3
1
ENTER INDEX NUMBER :1
USING 1- 9 KEYS
or Play mode, and then
Press SEARCH twice to display SEARCH
SELECT :
SET :
press NUMBER keys to
EXIT
: ACT I ON
FORWARD SEARCH :FF
in Stop or Play mode.
REVERSE SEARCH :REW
NEXT
:SEARCH
select recording
EXIT
:STOP
number.
2
Press FF to start
SEARCH
INDEX
PROGRAM END
PROGRAM END
• To calculate number,
SEARCH.
see below.
SEARCH START :FF
3
• To cancel, press
Press FF or REW to
Press ACTION to return to normal screen.
STOP or PLAY.
start search.
EXIT
:SEARCH
2
Play begins at search
INDEX SEARCH
Examples of Program End Search.
end. To search forward
or back 1 index, press
Fig. 1
FF or REW while screen
left is displayed (10
Program 1
Program 2 or BLANK
FORWARD SEARCH :FF
REVERSE SEARCH :REW
sec.).
the current tape position
Press SEARCH button
End Point
• To cancel, press
FF
STOP or PLAY.
Zero Search
Fig. 2
Program 1
BLANK
Program 2
BLANK
To quickly return to a specified tape location.
the current tape position
Press SEARCH button
End Point
FF
1
Press DISPLAY during play
to display Counter.
To Calculate Index Number
Fig. 3
the current tape position
Example 1:
Press SEARCH button
2
PLAY
1 2 : 0 0AM
To go to rec. 2 from rec. 4, enter 3 and press
0 : 0 0 : 0 0
Program 1
BLANK
Program 2
SP
REW.
If search
FF
exceeds a few
End Point
seconds in
BLANK area.
1
2
3
4
5
6
7
3
Continue to record, playback, etc.
Upon locating end point,
➛ search continues 7 sec. past end point,
Example 2:
4
➛ tape rewinds to 10 sec. before end point,
Press STOP.
To go to rec. 6 from rec. 2, enter 4 and press
➛ tape plays to end point and stops.
FF.
5
REW
1 2 : 3 0AM
CH 02
0 : 30 : 30
SP
Notes
1
2
3
4
5
6
7
• If Program End Search is started very
close to an index mark, that mark may be
skipped over.
NOTE:
indicates start points of each recording.
• To cancel, press PLAY or STOP.
STOP
1 2 : 3 1AM
CH 02
0 : 0 0 : 0 0
SP
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
*Important: If a remote control button does not work when pressed,
- 6 -
Commercial Skip
VCR fast forwards (skips) over 1~3 minutes
of recorded tape.
1
Press CM/ZERO in Play mode.
Press
• Press CM/ZERO repeatedly to change
to select REPEAT PLAY
skip time as shown below.
and press
to set ON
or OFF.
ON : Play repeats at
tape end or if
PLAY
unrecorded portion
over 30 sec. is
detected.
1st Press
1 min Skip
2nd Press
2 min Skip
3rd Press
3 min Skip
• No indication appears.
Press RESET
COUNTER at desired
position to reset to
"0:00:00".
Press CM/ZERO in Stop
mode to start ZERO
SEARCH.
• Unit will go into FF or
REW mode and stop at
the last point the
Counter was set to
0:00:00.
press the VCR button on the remote and try the button again.
- 7 -
Advertisement
Table of Contents
