Miele KM 360 G Installation Instructions Manual
Gas hobs
Hide thumbs
Also See for KM 360 G:
- Installation instructions manual (28 pages) ,
- Operating instructions manual (28 pages) ,
- Specifications (7 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Miele KM 360 G
Summary of Contents for Miele KM 360 G
-
Page 1: Installation Instructions
Installation instructions Gas hobs KM 360 G / KM 360-1 G KM 361 G KM 362 G / KM 362-1 G KM 363 G To avoid the risk of accidents or damage to the appliance it is essential to read these operating instructions before it is installed or used for the first time. - Page 2 Per questo se si vuole usare l'apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.
- Page 3 Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß...
-
Page 4: Table Of Contents
KM 360 G / KM 362 G ........ -
Page 5: Safety Instructions
Safety instructions Building in Fit wall units and extractor hood before fitting the hob, to avoid damaging the appliance. The veneer or laminate coating of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort. - Page 6 For any flammable objects, e.g. The hob may be installed above a utensil rails etc. a minimum safety Miele oven, if the work-top is at distance of 760 mm should be least 40 mm thick. maintained between it and the An electric fryer must not be appliance below.
-
Page 7: Appliance Dimensions And Worktop Cut-Out
Appliance dimensions and worktop cut-out KM 360 G / KM 362 G a Building-in depth b Mains connection box c Gas connection R - ISO 7-1 (DIN2999) -
Page 8: Km 360-1 G / Km 362-1 G
Appliance dimensions and worktop cut-out KM 360-1 G / KM 362-1 G a Building-in depth b Mains connection box c Gas connection R - ISO 7-1 (DIN2999) -
Page 9: Km 361 G / Km 363 G
Appliance dimensions and worktop cut-out KM 361 G / KM 363 G a Building-in depth b Mains connection box c Gas connection R - ISO 7-1 (DIN2999) - Page 10 Appliance dimensions and worktop cut-out ^ Prepare the worktop cut-out as shown in the diagrams. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 100 mm between it and a side wall or tall unit to the right or left of the hob.
-
Page 11: Installation
Installation Building in the appliance Securing the appliance ^ Place the gas hob in the prepared cut-out. ^ Feed the electricity connection cable through the cut-out and connect. ^ Make the gas connection, (see relevant section). ^ Secure the gas hob with the brackets a supplied, see illustration. - Page 12 Installation Do not let sealant get in between the hob frame and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the hob frame or the worktop.
-
Page 13: Electrical Connection
Electrical connection Connection should be made via a All electrical work should be carried suitable isolator or a double pole fused out by a suitably qualified and spur connection unit which complies competent person in strict with national and local safety accordance with national and local regulations and the on/off switch should safety regulations. - Page 14 Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations. It is most important that this basic safety requirement is tested regularly and if there is any doubt the electrical wiring in the home should be tested by a qualified...
-
Page 15: Gas Connection
Gas Connection Connection Connection to the gas supply, or Conversion to another type of gas is conversion from one type of gas to described under the relevant Section. another should only be undertaken by an approved and registered gas The gas connection must be installed installer in strict accordance with so that connection can be made either from inside or outside the kitchen unit,... -
Page 16: Natural Gas / Liquid Gas
Gas Connection Natural gas / liquid gas ^ The appliance is supplied with an R 1/2" - ISO 7-1 (DIN 2999) gas connection point. ^ An appropriate rigid connection and isolating valve must be installed for final connection. ^ The gas connection must be so sited that it is not adversely heated when the appliance is in operation. -
Page 17: Burner Ratings
Burner ratings Nominal rating for all gas types with the burner full on Burner Gas type KM 360 G / KM 360-1 G KM 362 G / KM 363 G KM 361 G KM 362-1 G Small Natural gas H 1.00... -
Page 18: Conversion To Another Type Of Gas
Conversion to another type of gas Jet table The jet markings refer to 1/100 mm of When converting to liquid gas, the the jet diameter. main jets and the small jets on all burners have to be changed. Contact your local gas supplier if the natural gas connection pressure is less Screw in the new jets according to than 18 mbar or higher than 25 mbar. -
Page 19: Changing The Jets
Conversion to another type of gas Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d. - Page 20 Conversion to another type of gas Wok burner ^ Take off the burner cap a, burner ring b and burner head c. ^ Loosen screws d and remove the cover plate. ^ Using an M7 socket spanner unscrew the main jets e (larger diameter jet) and f (smaller diameter jet).
-
Page 21: Changing The Small Jets
Conversion to another type of gas Changing the small jets (for all burners) To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Remove the operating controls by pulling them upwards. -
Page 22: After Changing The Jets
KM 360 G / KM 362 G In the highest setting the flame must When replacing the stainless steel have a distinctive and visible core. - Page 24 Alteration rights reserved / 1505 M.-Nr. 05 827 600 / 05 en - –...