Miele KM 360 Installation Instructions Manual
Hide thumbs
Also See for KM 360:
- Operating instructions manual (20 pages) ,
- Installation instructions manual (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele KM 360
Summary of Contents for Miele KM 360
- Page 1 Installation instructions Gas cooktops It is essential to read these operating and installation instructions before installing and using the appliance. This prevents both personal injury and damage to the appliance. en-AU, NZ M.-Nr. 05 827 671...
- Page 2 For trouble-free operation of the appliance, it is best to use it in the countries specified for use. For use in other countries, please contact Miele in your country. Repairs and other work by unqualified persons could be dangerous. Installation, maintenance work and repairs to electrical appliances must only be carried out by a Miele approved service technician.
-
Page 3: Table Of Contents
Contents Safety instructions for installation..............Safety distances ....................Installation notes ....................Detailed dimensions..................Installation dimensions ..................10 KM 360, KM 362 ....................10 KM 360-1, KM 362-1................... 11 KM 361 G, KM 363 G ..................12 Installation......................13 Gas connection....................15 Burner ratings ....................18 Electrical connection ..................20 Conversion to another type of gas .............. -
Page 4: Safety Instructions For Installation
Safety instructions for installation Risk of damage from incorrect installation. Incorrect installation can cause damage to the cooktop. The cooktop must only be installed by a qualified person. Damage from falling objects. Take care not to damage the cooktop when fitting wall units or a rangehood above it. - Page 5 Safety instructions for installation This appliance must not be installed and operated in mobile installations (e.g. on a ship). Carefully observe the safety clearances listed on the following pages.
-
Page 6: Safety Distances
Safety distances Safety distance above the Safety distances to the sides cooktop and back of the appliance Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall on one side (right or left). - Page 7 Safety distances Clearance underneath the appliance A minimum safety clearance of 30 mm must be provided underneath the appliance. Please note that clearance must also be provided for the installation of the flexible gas connection hose and mains electrical cable if the appliance is to be installed above a closed surface (e.g.
-
Page 8: Installation Notes
Installation notes Seal between the cooktop and Tiled worktop the worktop Grout lines and the hatched area underneath the cooktop frame must be smooth and even. If they are not, the Damage caused by incorrect cooktop will not sit flush with the installation. -
Page 9: Detailed Dimensions
Detailed dimensions Height of pan supports above the worktop surface a Vertical distance b Worktop surface c Pan support The vertical distance from the top of the pan supports to the surface of the worktop is 48 mm. Distances from burner to the edge of the appliance KM 362-1... -
Page 10: Installation Dimensions
*INSTALLATION* Installation dimensions All dimensions in this instruction booklet are given in mm. KM 360, KM 362 a Building-in depth b Mains connection box with mains connection cable, L = 2,000 mm c Gas connection R ¹/₂" - ISO 7-1 (DIN EN 10226) - Page 11 *INSTALLATION* Installation dimensions KM 360-1, KM 362-1 a Building-in depth b Mains connection box with mains connection cable, L = 2,000 mm c Gas connection R ¹/₂" - ISO 7-1 (DIN EN 10226)
-
Page 12: Km 361 G, Km 363 G
*INSTALLATION* Installation dimensions KM 361 G, KM 363 G a Building-in depth b Mains connection box with mains connection cable, L = 2,000 mm c Gas connection R ¹/₂" - ISO 7-1 (DIN EN 10226) -
Page 13: Installation
*INSTALLATION* Installation Preparing the worktop Installing the cooktop Create the worktop cut-out. Attach the sealing strip provided Remember to maintain the minimum underneath the edge of the cooktop. safety distances (see "Installation – Feed the mains connection cable Safety distances"). - Page 14 *INSTALLATION* Installation Securing the cooktop Functional check After installing the cooktop, ignite all burners to check that they are operating correctly: - The flame must not go out on the lowest setting, or when the control knob is turned quickly from the highest to the lowest setting.
-
Page 15: Gas Connection
Gas connection Check with your local gas supplier Risk of explosion due to an about the type of gas supplied and incorrect gas connection. compare this information with the If the gas connection is carried out type of gas quoted on the incorrectly, it may result in gas appliance's data plate. - Page 16 Miele. Conversion to another type of gas is described in the section Connect the cooktop to the gas “Conversion to another type of gas”.
- Page 17 Gas connection For natural gas models Setting the gas pressure The gas regulator is only included with The gas pressure must be set by the appliances which are set up for authorised gas fitter as shown on the connection to natural gas. The data plate: regulator must be connected directly Natural gas 1.0 kPa...
-
Page 18: Burner Ratings
Burner ratings Nominal ratings for KM 360, KM 360-1, KM 361 Burner Gas type Highest setting Lowest setting MJ/h MJ/h Auxiliary burner 3.85 0.70 ULPG 3.60 0.41 Normal burner 5.85 1.10 ULPG 6.35 0.97 Fast burner 10.35 1.70 ULPG 9.68 1.65 Total 25.90 ULPG 25.98 Nominal ratings for KM 362, KM 362-1... - Page 19 Burner ratings Nominal ratings for KM 363 Burner Gas type Highest setting Lowest setting MJ/h MJ/h Auxiliary burner 3.85 0.70 ULPG 3.60 0.41 Normal burner 5.85 1.10 ULPG 6.35 0.97 Fast burner 10.35 1.70 ULPG 9.68 1.65 Total 20.05 ULPG 19.63...
-
Page 20: Electrical Connection
Miele product must also be assured in their function and operation in isolated All electrical work must be carried out operation or in non-mains synchronous... -
Page 21: Conversion To Another Type Of Gas
*INSTALLATION* Conversion to another type of gas Changing the jets Risk of explosion due to an incorrect conversion. Disconnect the cooktop from the If the conversion to another type of electricity supply and turn off the gas gas is carried out incorrectly, it may supply. - Page 22 *INSTALLATION* Conversion to another type of gas Changing the main jets (wok burner) Remove the burner caps and the burner head . Loosen the screws and remove the cover plate. Using an M7 socket or open-end spanner, unscrew the main jets (larger diameter) and (smaller diameter).
- Page 23 *INSTALLATION* Conversion to another type of gas Removing the top of the Changing the small jets appliance You must remove the top of the appliance to change the small jets. Pull the control knobs off. Remove the loose burner components.
-
Page 24: Checking Operation
*INSTALLATION* Conversion to another type of gas Checking operation Refitting the stainless steel upper section Check all gas fittings for leaks. Reassemble the cooktop. Ignite all burners to check that they are operating correctly. - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting. -
Page 25: Service
Service Contact in case of fault In the event of any faults which you cannot remedy yourself, please contact Miele. You can book a Miele customer service call-out online at www.miele.com.au/ service or www.miele.co.nz/service. Contact information for Miele can be found at the end of this booklet. - Page 27 183 Featherston Street Miele Experience Centre South Melbourne: Wellington 6011 206-210 Coventry Street South Melbourne, VIC 3205 0800 464 353 (0800 4 MIELE) Miele Experience Centre and Office Sydney: www.miele.co.nz 3 Skyline Place Frenchs Forest, NSW 2086 Miele Experience Centre and Office Brisbane:...
- Page 28 KM 360, KM 360-1, KM 361, KM 362, KM 362-1, KM 363 en-AU, NZ M.-Nr. 05 827 671 / 07...