Electrical Requirements; Important Safety Instructions - Kenmore 79048902000 Installation Instruction

Important Notes to the Installer
1. Read aii instructions contained in these installation
instructions before installing the combination oven.
2. Remove all packing material from the oven compartments
before connecting the electrical supply to the wail oven.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
5. Oven door may be removed to facilitate installation.
6. THIS COMBINATION OVEN IS NOT APPROVED
FOR STACKABLE OR SIDE=BY=SIDE INSTALLATION.
Important Note to the Consumer
Keep these instructions with your Owner's Guide for future
reference. Do not discard oven removal tools found in the
literature bag.
IMPORTANT SAFETY
INSTRUCTIONS
* Be sure your combination oven is installed and
grounded properly by a quallfied installer or service
technician.
* This wall oven must be elecfrlcaily grounded in
accordance wlfh local codes or, in their absence,
wlfh the Natlonal Elecfrlcal Code ANSJ/NFPA No.70=
latest edition in United Sates, or wlth CSA Standard
C22.1, Canadian Elecfrlcal Code, Part 1, in Canada.
Stepping, leaning or sitting on the door
of thls wall oven can result in serious injuries and can
also cause damage to the wall oven.
* Never use your wall oven for warming or heating
the room. Prolonged use of the wail oven without
adequate ventilation can be dangerous.
The elecfrlcal power to the oven must be
shut off while llne connections are being made. Failure
to do so could result in serious injury or death.
1. Carpentry
Refer to figure 1 for the dimensions applicable to your
appliance, and the space necessary to receive the
combination oven. The oven support surface may be solid
plywood or similar material, however the surface must be
leveled from side to side and from front to rear.
2. Electrical Requirements
This appliance must be supplied with the proper voltage and
frequency, and connected to an individual, properly grounded
branch circuit, protected by a circuit breaker or fuse. To
know the circuit breaker or fuse required by your model, see
the serial plate to find the wattage consumption and refer to
table A to get the circuit breaker or fuse amperage.
Applianc e Protection Appliance , Protection
Rating Watts Circuit Rating Watts Circuit
240V Recommended 208V Recommended
Less t han4800W 20A Less t han4100W 20A
4800W
-
7200W 30A 4100W
-
6200W 30A
7200W
-
9600W 40A 6200W
-
8300W 40A
9600W and+ 50A 8300Wand+ 50A
Table A
Observe all governing codes and local ordinances
1. A 3-wire or 4-wire single phase 120/240 or 120/208 Volt,
60 Hz AC oniy electrical supply is required on a separate
circuit fused on both sides of the line (red and black wires).
A time-delay fuse or circuit breaker is recommended. DO
NOT fuse neutral (white wire).
NOTE: Wire sizes and connections must conform with the
fuse size and rating of the appliance in accordance with the
American National Electrical Code ANSI/NFPA No. 70-latest
edition, or with Canadian CSA Standard C22.1, Canadian
Electrical Code, Part 1, and local codes and ordinances.
An extension cord should not be used
wlfh fhls appliance. Such use may result in a fire,
elecfrlcal shock, or other personal injury. If you need a
longer power cord you can purchase a 10' (3 m) power cord
kit by calling the Service Center.
.
These appliances should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from the appliance should be
connected directly to the junction box. The junction box
should be located as shown in Figure 1 and with as much
slack as possible remaining in the cable between the box
and the appliance, so it can be moved if servicing is ever
necessary.
3. A suitable strain relief must be provided to attach the
flexible armored cable to the junction box.
In cotd weather shipping and storage
conditions, make sure that oven is in final location at least
three (3) hours before switching on power. Switching on
power while oven is still cotd may damage the oven controls.