Advertisement
Electrical Shock Hazard
Turn power supply off before connecting
wires,
Use 8-gauge solid copper wire,
Electrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
This range may be connected directly to the fuse
disconnector circuit breaker box; or with a U.L-
listed, 40-ampere range power supply cable,
Depending on your electrical supply, make the
required three-wire or four-wire connection.
U.L.-listed conduit
connector,
1, Disconnectthe power supply.
2, Remove the knockout for the power supply
cable.
3. Assemble a U.L.-listed conduit connector in
the power supply cable opening,
4. Strip outer covering back 3 inches from end,
exposingwires, Strip the insulation back
! inch from the end of each wire.
5. Form the bare wire into a
II u
"U"-shaped hook,
6. Insert the power supply cable
through the conduit connector,
allowing enough slack to easily
attach the
wiring terminal block,
7, Complete electrical connection according to
your type electrical supply ("Three-wire
electrical connection" or "Four-wire
electrical connection,")
Three-wire electrical connection:
silver-colored
..awrou.u _
terminal block
link
SCreW
line 2
Figure 6
r
neutral
|white wire)
U,L,-listed conduit
connector and power
supply cable,
Use this method ONLY if local codes PERMIT
connecting cabinet-ground conductor to
neutral wire of power supply cable.
& Use the brass terminal nuts attached to the
inside of the terminal block cover to
connect the neutral wire (white wire) to the
silver-colored terminal screw on the
terminal block. See Figure 6,
9, Connect the other two wires to outer
terminal screws on the terminal block,
See Figure 6,
10. Do Not loosen factory-installed nuts
already on the terminal, Tighten nuts
with 3/8" nut driver for proper electrical
connection.
11, Tighten the locking ring and clamping
screws of the conduit connector,
12. Replace the terminal block cover.
Check that
cooktop
elements heat
properly
_ .'_ Check that oven
}_)_ heatsproperly
_i:_'_i_ R emove shipping
_ _ _,_' material
Removeoven
racksandparts
package
\
\
\
.... _',Levelrange
Four-wire electrical connection:
s_rew
Figure7
•silver-_olored
screw
neutral wire
from power
supply cable
line 2
Figure 8
listed
conduit
connector end
power supply
cable
Use this method for mobile homes and
whenever four-wire installation is required.
8. Remove the ground-link screw from the
range frame. Save the ground-link
screw, Bend up the ground link so that it
does not contact the range. See Figure 7.
9. Connect the bare ground wire from
power supply cable to the range using the
ground-link screw, The ground wire
must be attached first and must not
contact any other terminal. See Figure 8,
10. Connect the neutral wire (white wire) to the
center, silver-colored terminal screw on the
terminal block using the brass terminal
nuts that are attached to the inside of the
terminal block cover, See Figure 8.
11. Connect the other two wires to the outer
terminals on the terminal block.
See Figure 8.
12. Do NOT loosen the factory-installed nuts
already on the terminal, Tighten nuts with
3/8" nut driver for proper electrical
connection,
13. Tighten the locking ring and clamping
screws of the conduit connector,
14. Replace the terminal block cover.
Operating
position
Before moving range across floor, checkthat
range is still on cardboard shipping base to
protect floor covering,
anti-tip
bracket...
range foot
== Making sure the anti4ip bracket is
installed:
• Look for the anti-tip bracket securely attached
to floor.
• Slide range back so rear range foot is under
anti-tip bracket.
==Ifinstalling the range in a mobile home,
you MUST secure the range to the floor. Any
method of securing the range is adequate as
long as it conforms to the standards in the
"Mobile home installation" instructions, Page 2.
0
mPlace rack in oven, Place level on rack,
first side to side; then front to back.
If range is not level, pul! range forward until rear
leveling leg is removed from the anti-tip bracket.
Use 3/8" drive ratchet and channe] lock pliers to
adjust leveling legs up or down until range is
level. Push range back into position, Check that
rear leveling leg is engaged in anti-tip bracket,
Note: Oven must be level for satisfactory baking
conditions.
II •Replace the storage drawer or lower
t
panel,
Page5
Advertisement
