![Harman Kardon DRIVE + PLAY [HK-DP1EU] Owner's Manual](https://static-data2.manualslib.com/product-images/35a/642606/harman-kardon-drive-play-hk-dp1eu-car-stereo-system.jpg)
Advertisement
Advertisement
Table of Contents
Related Manuals for Harman Kardon DRIVE + PLAY [HK-DP1EU]
Summary of Contents for Harman Kardon DRIVE + PLAY [HK-DP1EU]
- Page 1 Owner’s Manual...
-
Page 2: Ipod Software
Drive + Play’s warranty depends on the laws in the country in to your iPod may occur. which it was purchased. Your local Harman Kardon retailer can help you determine the length of your warranty. To register Lost Data your product, please visit us at: www.harmankardon.com... -
Page 3: Installation
INSTALLATION Choosing Installation Locations INSTALLATION IMPORTANT: Drive + Play should be installed according to Parts List these instructions and relevant regulations. No part of this Drive + Play includes the following components and parts: system should obstruct the driver’s view of the road or vehicle controls or information displays necessary for safely operating •... - Page 4 Electronics Enclosure Location Choosing an Audio Interface The Electronics Enclosure contains the wireless FM transmitter Referring to the Wiring Diagram on the next page, you can and the power supply for the three components. You can install interface the Drive + Play’s audio output to your mobile audio it under a seat, in the center console compartment, in the glove system in three ways: box or behind the radio.
-
Page 5: Wiring Diagram
INSTALLATION Wiring Diagram iPod Text Display Control Knob Audio Input/Output Jacks Tip = LEFT RIGHT = Ring Sleeve = GROUND 3.5mm Stereo Mini-Plug Cable iPod Cable Wireless FM Transmitter (Only available in Head Unit/Radio Electronics Enclosure selected countries) Side Back Removable Antenna In Power Connection... -
Page 6: Installing Components
Installing Components b. Select another viewing angle position (middle or top). Reassemble the parts in reverse order and tighten the Installing the Electronics Enclosure recessed hex screw. At the selected site, install the Electronics Enclosure. Use either the enclosed cable ties or mounting screws, as shown below. Hex Key Display Base... - Page 7 INSTALLATION b. At the proposed site, wipe the surface and exposed 1. Place the Control Knob at the site and check the operation mounting plate with one of the enclosed alcohol pads. angle with the default 30° base. If it meets your needs, Allow both to dry.
-
Page 8: Operating
Installing Components Control Knob Installing the Control Knob (continued) With 0° Base 2. At the base (below the cable), using the 1.5mm hex key, loosen (but do not remove) the hex setscrew. 3. To install the Control Knob with adhesive tape, perform the following steps or skip to step 4: a. -
Page 9: Operation
NOTE: If the preset FM frequencies are already assigned to FM stations in your listening area, then use Custom FM 2. Drive + Play’s Text Display will show the Harman Kardon Frequency (below) to select an unused frequency. splash screen first, followed by the Now Playing screen. - Page 10 Initial Setup (continued) groups, the third group will appear after a few seconds, followed by the first group again. If Auto Scroll is enabled, Setting FM Transmission (continued) the character groups will change automatically. • To select a Custom FM Frequency: •...
- Page 11 • Drive + Play Menu > Genres > select a genre > select an artist 2. After a few seconds, you will see the Harman Kardon splash > select an album > select a song. screen, followed by the Now Playing screen. At this point, all Browsing Composers Drive + Play settings have been reset.
-
Page 12: Troubleshooting
Problem: All features and specifications are subject to change without notice. Harman Kardon and Harman International are registered trademarks, and Drive + Play is a Hearing static when playing the iPod with wireless trademark, of Harman International Industries, Incorporated.