Whirlpool SC8720EDB06 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Whirlpool Manuals
  4. Cooktop
  5. SC8720EDB06
  6. Installation instructions manual
Whirlpool SC8720EDB06 Installation Instructions Manual

Whirlpool SC8720EDB06 Installation Instructions Manual

30" gas downdraft cooktop
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
||
Downdraft Cooktop
Modules selected at time of purchase.
Quick Reference
Table of Contents:
Pages
[--1-]Before you start
[--1-]Cutout dimensions
[--1-]Clearance dimensions
[21 Product dimensions
F_ Tools and materials needed
[21 Parts supplied
[_1 Electrical requirements
[31 Gas supply requirements
[]
[=_ Venting requirements
r_
[61 Installation steps
[]
Gas conversions
IBac k coverl Cooktop removal
Need assistance?
Check your Use and Care Guide for a toll-free number to call, or
call the dealer from whom you purchased the cooktop when you:
[] Have questions about the cooktop installation or operation.
[] Need to obtain the name and number of an authorized service
company.
The dealer is listed in the Yellow Pages of your phone directory
under "Appliances -- Household -- Major -- Service and Repair."
When you call, you will need:
[] The cooktop model number.
[] The cooktop serial number.
Both numbers are listed on the model/serial rating plate, located
on the bottom of the right side of the downdraft plenum.
Write both numbers down now before installing cooktop.
Model #
Serial #

Advertisement

Table of Contents
loading

Related Manuals for Whirlpool SC8720EDB06

Summary of Contents for Whirlpool SC8720EDB06

  • Page 1 Quick Reference Table of Contents: Pages [--1-]Before you start [--1-]Cutout dimensions [--1-]Clearance dimensions [21 Product dimensions F_ Tools and materials needed [21 Parts supplied [_1 Electrical requirements [31 Gas supply requirements [=_ Venting requirements [61 Installation steps Gas conversions IBac k coverl Cooktop removal Need assistance? Check your Use and Care Guide for a toll-free number to call, or call the dealer from whom you purchased the cooktop when you:...
  • Page 2 WARNING: To reduce the risk of fire, guideline and safety standards such as electric shock, or injury to persons, observe those published by the American Society the following: for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the Installation work and electrical wiring must Your safety and the safety local code authorities.
  • Page 3 30" (76.2 cm) minimum when _t Installation location should higher than 18" (45.7 cm} ----------_l provide sufficient room for: • Removing grease containers..• Accessing gas regulator. Side clearance -- 2" (5.1 cm) minimum clearance is required. 6" (15.2 cm) clearance between side of cooktop and side wall is maximum upper...

  • Page 4: Natural Gas

    certified by CSA International for Natural or shutoff valve "open" position L.P. gas usage with appropriate conversion. (See "Gas conversion" instructions, Page 7). to downdraft The model/serial rating plate (located on the cooktop right side of the downdraft plenum) lists the type of gas that can be used.
  • Page 5 inside wall outside wall peninsula peninsula cabinet or island 7-9/16" cabinet trans, 3-1/4" x 10'_ ]] II transition for venting elbow_ through floor \3-1/4 ''-" tn''^ insidewail to roof directly outside between floor joists or overhang cabinet toe space to outside opening for venting through rear wall /5"...

  • Page 6: Installation

    Note: Cooktop shown with optional grill accessory. Check each burner for proper flame Gas supply connection Vent system connection Preparation Vent connection Installation Insert downdraft cooktop into Connect vent system. See cutout. Check that: "Venting requirements," pages 3-4. Use Excessive Weight Hazard duct tape to seal all joints.

  • Page 7: Check Operation

    Check operation Push in and turn each surface burner control knob to "LITE" position and then to "LO" position. The low flame should To adjust be a minimum, steady blue flame. grill burner t !!1 II_l air shutter Do Not use a metaNblade to pry off control knob;...

  • Page 8: Lp Gas Conversion

    Orifice hoods: right rear burner Natural -- Brass, drill size #53 (orifice did. 0.0595") L.P. = BJue,drill size #63 (orifice did. 0.037") left rear burner pressure regulator left burner Orifice hoods: Natural -- Green, drill size #55 (orifice did. 0.052") L.P.= Zinc, drill size #66 (orifice did.

  • Page 9: If You Need Assistance

    When you call, you will need the cooktop model number and serial number. Both numbers can be found on the model/serial rating plate located on the bottom of the burner box. Part No. 8101P350-60/8284676 Benton Harbor, Michigan 49022 Printed in U.S.A. © 2000 Whirlpool Corporation...

Table of Contents