Advertisement
Quick Links
iNSTALLATION INSTRUCTIONS
Gather the requiredtoolsand parts beforestartingInstallation.
iMPORTANT:Observe all governingcodes and ordinances.
Read and follow the instructions providedwith any tools listed
Check the locationwhere air conditJonerwlll b e nstelled.Proper
here.
installat_on i s yourresponsiblli_j. M ake sure you haveeverythin_
Took; Needed
necessaryfor correct, i nstallation.
The locationshould provide:
[]
Flat-bladeand Phillips
[]
Tape measure
[]
Groundedelecl_icaloutietwithin 4 ft(122 cm) of where b_e
screwdrivers
[]
Drill and _" or smallerbit
power cordexitsthe air conditioner.
[]
Level
NOTE: Do not usean extensioncord.
[]
Free movement of air in roomto be cooled.
Through.the,Waft Instahtion:
In additionto the tools listed above,the followingtoolsare
[]
A large enoughopeninglor Lheair conditioner,
needed for through-the-wallInsta lation.
[]
Adequatewall supporr.forweight a! air conditioner. A ir
[]
Saw
[]
1" (2,5 cm) orthicker
conditioner weighsbeLween50 and 60 Ibs [22to 28 kg),
lumber
MOTE:Cabinet louversmust _otbe obstructed.Air must be able
[]
Woadpreservative
[]
#10 x 1" wood screws (7)
to pass freelythrough thecabinet,louvers.
[]
Caulk
Parts SuppFmd(on some models)
Check that.all parts are includedin paris package,
C
D
E
F
A. Cebtnet touvers
screws
_)
G.Topchannel
O.JlO x _" pan-head
H, Sidecurtains ( 2J
Phillips screws _3)
L Fo#m seal
NOTE: Installationparts are suppliedlor double-hungwindows
up to 40 (101.6 cm) wide, AspecialWide Window Kit.isavailable
from yourdealeror servicecenter.See "Accessories."
PIN 66129901290
1
Advertisement
Related Manuals for Frigidaire FAQ085S7A11
Summary of Contents for Frigidaire FAQ085S7A11
- Page 1 iNSTALLATION INSTRUCTIONS Gather the requiredtoolsand parts beforestartingInstallation. iMPORTANT:Observe all governingcodes and ordinances. Read and follow the instructions providedwith any tools listed Check the locationwhere air conditJonerwlll b e nstelled.Proper here. installat_on i s yourresponsiblli_j. M ake sure you haveeverythin_ Took; Needed necessaryfor correct, i nstallation.
- Page 2 Window Installation Window opening measurements: opening width, m 22.2" to 40" (56.3 cm to 101.6 14"(35.5cm) mm#ni4mopeninghe_gl_L A. 22.2" (56.3 cm) minimum e. 14"(355cm) minimum Through,the.Waft lnstafia_n The wall opening measurements should be: Width: 19V_(48.4 cm) plus twice thickness of wood used to build frame, Height: 13"...
-
Page 3: Installation Instructions
iNSTALLATiON iNSTRUCTiONS Removethe window lock bracket and screw |rein the air Ex_sslw Weight Hazard conditJoner a nd setaside.(on some models) Use two or mor_ people)to move)and Inee_ll sir _orldltloner. Fmilumto do so €_n result in back or o_herinjury. Remove packagk_g mab_dels [] Removeand disposeof/recyclepackagingmaterials. - Page 4 NOTES: Bottom view Handle the air conditionergently, Be sure yourair conditioner cabinetdoes not fall out o( the openingduring installation or removal. The place wherethe powercord exits the air conditioner shouldbe no more than 4 (t(122 cm) from a grounded 3 prongoutlet Do not blockthe louvers on the front panel.
- Page 5 install _binet into Window Attach Side Curtains to _ndow Frame 1, Pullthe left-hand curtainout untilitfits intothe window Handlethe air conditioner gently, channel,Use a %2"drillbitto drilla starter holethrough the Be sureyour air conditioner cabinet does notfall outer the hole in the curtainhousingand into the lower window sash, openingduringinstallationor removal.
- Page 6 Comp_te installation 1, Insert.sealbehindthe Lopof the towerwindowsashand againstthe glassof the upper window, 2, Place the window-lockbracketon top of towerwindow and againstupper window sash. 3, Use a _/_" drillbitto drilla starterholesthroughthe holes in each bracket intothe windowsash Attachthe window-lockbracket to the window sash with #10 x s/4.round-headscrewsto securewindow in place.
- Page 7 Use l" (2.5 cm) or thicker lumberfor woodframe. 2. Use a levelto checkthatcabinetis levelside to side. A. Level A. Outside width 3. Check thatairconditionercabinetis tilted to theoutside so B. Outside height C. Depth thatwater will run to the outside.Thecabinet shouldslope at least half-a-bubble towards the rear.
- Page 8 ! Electrical Shock Hazard J Connect green ground wire to ground screw. 5. tnserttronttabs of frontpanel into top of cabinetand swing front intoplace, Failure to do so can result in death or electrical shock. 6. Attach bottomIront of panelwith frontpanelscrews, Replace controlknobs{onsome models), 3.