Table of Contents
Advertisement
OPERATION
A
WARNING:
Do
not
allow familiarity
with products to
make
you careless
. Remember
that a careless
fraction
of
a
second is sufficient to inflict serious
injury.
A
WARNING:
Always
wear eye
protection
with side
shields
marked
to comply with
ANSI
Z87.1.
Failure
to
do so
could result in
objects being thrown
into your
eyes
resulting
in
possible
serious injury.
A
WARNING:
Do not use any attachments or
accessories
not
recommended by
the
manufacturer
of this product. The
use
of attachments or
accessories
not recommended
can
result
in
serious
personal
injury.
APPLICATIONS
You may use
this
product for the
purpose
listed
below:
•
Charging and maintaining compatible 12 V-19.2
V
nickel-cadmium battery packs
CHARGER CAN BE USED WITH THE FOLLOWING
BATTERY PACKS:
For use with 19.2V nickel-cadmium battery
packs,
see
tool/appliance/battery pac k/charger correlation
supplement 988000-272.
Ni-Cd
I
12V
I
14.4V
I
18V
I
11068
I
11044
I
11045
CAUTION:
If
at any point during the charging
process none of the
LEDs
are
lit
••
remove the
bat-
tery
pack
from the charger
to
avoid damaging the
product.
DO NOT insert another
battery.
Return
the
charger and battery to
your nearest
authorized
ser-
vice center for service
or
replacement.
CAUTION:
Charge in a well
ventilated
area.
Do
not
block
charger
vents.
Keep
them
clear to allow proper
ventilation.
LED FUNCTIONS OF CHARGER
See
Figures
2 -
4,
pages i - ii.
CHARGER LED WILL BE ON TO INDICATE
STATUS OF CHARGER AND BATTERY PACK:
• Red LED
on, Green
LED off
=
Power
to charger is on.
• Red LED
flashing, Green LED off =
Battery
is being
tested
.
• Red LED
fading, Green
LED off
=
Battery is defective.
• Red LED
on, Green LED flashing
=
Battery
is charging.
•
Red LED
off,
Green
LED
on
=
Battery
is
fully charged
.
•
Red LED off, Green LED fading on and off
=
Battery
is fully charged; charger
is
in
Energy
Save mode.
Charger will
periodically
wake from
Energy
Save mode
to ensure the battery pack remains in a fully charged
state.
CHARGING A BATTERY PACK
Battery packs
are shipped in a
low
charge condition to
prevent possible problems.
Therefore,
you
should charge
them before first use.
If
the charger does not charge
the
battery pack
under
normal circumstances
,
return both the battery pack and
charger to
your
nearest Authorized Service Center for
electrical
check.
•
Use battery pack only
with
the recommended
charger.
•
Connect the charger to the power
supply.
Make sure
the power supply
is
normal household
voltage,
120
volts,
AC only,
60
Hz.
• Place the
battery pack in the charger aligning raised Fib
on the battery pack with the groove in the charger.
• Press
down on the battery pack to be
sure
contacts on
the battery pack engage properly with contacts in
the
charger.
•
Do
not
place the charger and battery pack in
an area
of extreme
heat
or cold
.
They
will
work best
at
normal
room temperature.
NOTE: The
charger
and battery
pack should
be placed
in
a
location
where the temperature is more than
50°F
but less
than
100°F.
• The battery
pack
will
become slightly
warm
to
the
touch
while charging. This is normal and does
not
indicate
a
problem.
6
- English
Hide quick links:
Advertisement
Table of Contents
