Contents Names of the parts Safety precautions Installation and adjustment Preparation before washing The musts in washing Usage of the detergent Washing sequence Disposal after washing Trouble-Shooting *Answers to question Packing list *Specification...
Names of the parts Drain switch Wash selector Wash timer Water-filling entrance water-filling translation Control panel Bypass channel Water level adjusting lever Overflow filter Lint filter Drain hose Pulsator Cabinet handle Wash tub Base frame Notes: All illustrations in this Manual are given for reference only. Your products and accessories may show differences from these illustrations due to our continuous improvement.
Safety precautions Please insert the power cord into special receptacle with rated vol- tage.Be sure to use single-phase three pins receptacle.The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector. Earth If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department.
Safety precautions Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine.
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter Put the underside of the lint filter into overflow filter then push the upside into overflow filter After installation, please refer that the lint filter installed to the right station, otherwise the lint...
How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Extend the drain hose from the side of spin tub Put soft items on the ground. Lean the machine down gently with the front surface facing the ground.
Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put down the drain hose .
The musts in washing Usage of the detergent How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laun- dries with color or pattern as they are prone to lose color.
Washing sequence Wash selector Wash timer (If to set less than 2 min, Intensity can be Soft, you should first surpass 6 min or Standard) and then turn back.) STANDARD SOFT WASH TIMER WASH SELECTOR Wash 1 Inlet selector (1) Set inlet selector to (2 )Adjust water level rod to a position as needed.
Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Proper The laundries are slanting (2) Close the inner and outer cover of the spin tub. (3) Spin for 1-2 minutes.
Rinsing Rinse with water-filing 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing.
Spinning 1. Put the laundries into the spin tub evenly and smoothly. 2. Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3. Spin Select suitable spin time according to the laundries, and do spinning. During spinning, if there's abnormal sound, it is generally owing to slanting placement of the laundries.
Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing.
Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside overflow filter ( as indicated in Figure 1). 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. 4.
Trouble-shooting Answers to question When the remained water is frozen Prevent the freezing (be sure to discharge the water completely after using) After complete draining, set the "DRAIN SELECTOR" at "OFF" . If it is set at "DRAIN", it will be rather difficult for the frozen water to melt.
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
Packing list Name User's manual Water inlet hose Gland Twin-tub washing machine Specification Water level Water quantity about (L) Rated voltage/Rated Frequency Rated input power for washing Rated input power for spinning Standard rated washing capacity(kg) Largest rated washing capacity(kg) Standard rated spinning capacity(kg) Injection pressure(MPa) Quantity...