removed from these pins. Please note that C means
"common" here and both C pins are electrically con-
nected and identical.
PROGRAMMING the 12v TRIGGER
By default the T2 triggered output is inactive. To
program this output to become active , whereupon
a control voltage of 12Vdc will appear across T2 & C
terminals whenever a specific source is selected, use
the handheld remote control as follows:
•
Select the source that you want to coincide with
T2 going active.
•
While pointing the remote control at the BP17,
press the CODE button, followed by the three digit
code "247" using the keys numbered 1 through
0 in the illustration at the left. On your remote
control these keys, or buttons, are labeled AUX/PH
(2), TUNER (4), D1 (7).
•
The three digit code should be entered within a
few seconds of pressing CODE button or the unit
will automatically return to normal operation.
•
To clear the T2 trigger output, press the CODE but-
ton followed by the 3 digit code "248": AUX/PH (2),
TUNER (4), D2 (8).
OPTIONAL IR REMOTE CONTROL
The Bryston model BR2 hand-helf
infra-red remote control is avialable
for use with the BP17. The BR2 can
also control many other Bryston pre-
amps and power amps. It features a
solid machined aluminum enclusure
and push-buttons and a back-lit but-
ton panel that will turn both ON (mo-
tion triggered) and OFF (inactivivity
timeout) automatically.
When used with the BP17 the BR2
remote allows selection of all sourc-
es, volume up or down (the volume
control is a motor-driven design),
mute, left/right balance, power on/
off and discrete code entry.
We recommend maintaining a direct
line-of-sight between the hand held
remote unit and the front of the BP17
to ensure the most efficient operation
of the remote features.
PROGRAMMING the BR2 REMOTE
The automatic motion-sensing backlight function in
the optional BR2 handheld infra-red remote control
unit can be disabled by entering the 3 digit code "792"
as follows:
1) Press and hold the CODE button for 5 seconds. Re-
lease when the LED flashes red.
2) After the LED stops flashing, enter the 3 digit code
"792" by pressing the buttons D1, D3 then AUX/PH
3) To re-enable the motion-sensing backlight func-
tion, repeat steps 1 and 2 above
To completely disable the backlight, enter the 3 digit
code "797" as follows:
1) Press and hold the CODE button for 5 seconds. Re-
lease when the LED flashes red.
2) After the LED stops flashing, enter the 3 digit code
"797" by pressing the buttons D1, D3 then D1
3) To re-enable the backlight repeat steps 1 and 2
above
SENDING CODES to the BP17 via the
BR2 REMOTE CONTROL:
Press the CODE button on the remote control (the red
LED will light) and then enter the 3 digt code, as listed
in the "Wired RS-232 Remote Control" section" below.
The LED will flash to confirm transmission and then ex-
tinguish.
000: power off
001: select analog source 1 (A/D)
002: select analog source 2 (AUX/PH)
003: select analog source 3 (CD)
004: select analog source 4 (TUNER)
005: select analog source 5 (TV)
006: select analog source 6 (VIDEO)
007: volume up
015: power on/off toggle
008: volume down
019: balance left
020: balance right
029: power on
BP17 PREAMPLIFIER
058: mute on
059: mute off
061: record monitor toggle
062: record monitor on
063: record monitor off
081 - select digital source 1 (D1)
082: select digital source 2 (D2)
083: select digital source 3 (D3)
084: select digital source 4 (D4)
245: set/reset BYPASS mode
247: Set Trigger 2 for current source
248: Clear Trigger 2 for current source
255: System reset; restore defaults