Advertisement
Before Starting
Tools You Will Need
For leveling legs and Anti-Tip Bracket:
Adjustable wrench or channel lock pliers
5/16" Nutdriver or Flat Head Screw Driver
•
Electric Drill & 1/8" Diameter Drill Bit (5/32" Masonry Drill
Bit if installing in concrete)
For gas supply connection:
Pipe wrench _
For burner flame adjustment:
Phillipshead _
and
blade-type screwdrivers
For gas conversion (LP/Propane or Natural):
•
Open end wrench - 1/2"
Additional Materials You Will Need
•
Gas line shut-off valve _,'_
Pipe joint sealant that resists action of LP/Propane gas
•
A new flexible metal appliance conduit (1/2" NPT x 3/4"
or 1/2" I.D.) must be design certified by CSA International.
Because solid pipe restricts moving the range we
recommend using a new flexible conduit (4 to 5 foot
length)
for each new installation
and additional
reinstallations.
•
Always use the (2) new flare union adapters (1/2" NPT x
3/4" or 1/2" I.D.) supplied with the new flexible appliance
conduit for connection of the range.
Normal Installation Steps
1.
Anti-Tip
Bracket
Installation
Instructions
Important Safety Warning
To reduce the risk of tipping of the range, the range must be
secured to the floor by properly installed anti-tip bracket and
screws packed with the range. Failure to install the anti-tip
bracket will allow the range to tip over if excessive weight is
placed on an open door or if a child climbs upon it. Serious
injury might result from spilled hot liquids or from the range
itself.
If range is ever moved to a different location, the anti-tip
brackets must also be moved and installed with the range.
Instructions are provided for installation in wood or cement
fastened to either the floor or wall. When installed to the wall,
make sure that screws completely penetrate dry wall and are
secured in wood or metal. When fastening to the floor or wall,
be sure that screws do not penetrate electrical wiring or
plumbing.
A.
S.
3
Locate the Bracket Using the Template- (Bracketmay
be locatedon eitherthe left or rightside ofthe range. Use
the information below to locate the bracket iftemplate is
not available). Mark the floor or wall where left or right
side ofthe rangewillbe located. If rear ofrange isagainst
thewall or no further than 1-1/4" fromwall when installed,
you may use the wall or floor mount method. If molding
is installed and does not allow the bracket to fit flush
against the wall,remove moldingor mountbracket to the
floor. For wall mount, locate the bracket by placing the
back edge of the template against the rear wall and the
side edge of template on the mark made referencingthe
side of the range. Place bracket on top of template and
mark locationofthe screw holes in wall. If rear of range
is further than 1-1/4" from the wall when installed,attach
bracket to the floor. For floor mount, locate the bracket
by placing back edge of the template where the rear of
the rangewillbe located. Mark the locationofthe screw
holes, shown in template.
Drill Pilot Holes and Fasten Bracket - Drill a 1/8" pilot
holewhere screws are to be located. If bracket is to be
mountedto thewall, drill pilot hole at an approximate20°
downwardangle. If bracket isto be mountedto masonry
or ceramic floors,drill a 5/32" pilot hole 1-3/4" deep. The
screws provided may be used in wood or concrete
material. Usea5/16" nut-driver orflat head screwdriver
to secure the bracket in place.
FASTEN BRACKET (WALL O hFLOOR M OUNTING)
--_r
i<--1-1/4"
Max
Leveling Leg --
Wall Mount
Wall Plate
I
J
Floor Mount
_!
p Bracket
FASTEN BRACKET
(FLOOR MOUNTING
ONLY)
--'-_l
- More Than
Leveling Leg --
1-1/4"
Floor Mount
v
p Bracket
Advertisement
