Advertisement
Available languages
Available languages
Important
Notes to the Installer
1.
Read all instructions contained in these installation
instructions before installing the cooktop.
2.
Remove all packing material before connecting the
electrical supply to the cooktop.
3.
Observe all governing codes and ordinances.
4.
Be sure to leave these instructions with the
consumer.
5.
Only certain cooktop models may be installed over
certain built-in electric oven models. Approved
cooktops and built-in ovens are listed by the MFG ID
number and product code.
Important
Note to the Consumer
Keep these instructions with your Use and Care Guide
for future reference.
An extension
cord must not be used
with this appliance.
Such use may result in a fire,
electrical shock, or other personal injury.
3.
The appliance should be connected to the fused
disconnect (or circuit breaker) box through
flexible armored or nonmetallic
sheathed cable.
The flexible armored cable extending from this
appliance should be connected directly to the
grounded junction box. The junction box should be
located as shown in Figure 2 with as much slack
as possible remaining in the cable between the box
and the appliance, so it can be moved if servicing
is ever necessary.
4.
A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.
I PO
NT SAFETY
I
o
STR
CTI
Be sure your cooktop is installed and grounded
properly by a qualified
installer or service
technician.
This cooktop must be electrically
grounded
in
accordance
with local codes or, in their absence,
with the National
Electrical
Code ANSI/NFPA
No.
70--latest
edition in the United States.
The electrical
power to the cooktop
must be shut off while line connections
are being
made. Failure to do so could result in serious
injury or death.
Provide
Electrical
Connection
Install the junction box under the cabinet and run
120/240 or 120/208 Volt, AC wire from the main circuit
panel. NOTE: DO NOT connect the wire to the circuit
panel at this time.
Electrical
Requirements
Observe all governing
codes and local ordinances.
1.
A 3-wire or 4-wire single phase 120/240 or
120/208 Volt, 60 Hz AC only electrical supply is
required on a separate circuit fused on both sides
of the line (time-delay fuse or circuit breaker is
recommended).
DO NOT fuse neutral.
2.
A circuit breaker or fuse rated at 50 Amp is
recommended
(40 Amp minimum).
NOTE: Wire sizes and connections
must conform with
the fuse size and rating of the appliance in accordance
with the National Electrical Code ANSI/NFPA
No.
70-latest
edition and local codes and ordinances.
Unpacking
Instructions
1.
Unpack and visually inspect the cooktop.
2.
Be sure the bottle of cleaner conditioner packed
in the literature bag is left where the user can
find it easily. It is important that the ceramic-glass
cooktop be pretreated before use. See Cooktop
Cleaning
and Maintenance
section in the Use
and Care Guide,
Electrical
Connection
Connect the flexible armored cable that extends from
the surface unit to the junction box using a suitable
strain relief at the point the armored cable enters the
junction box. Then make the electrical connection
as
follows.
Electrical
ground
is required
on this appliance.
This appliance
is equipped
with a
copper
conductor flexible
cable. If connection
is made to aluminum
house wiring,
use only
special connectors
which are approved
for joining
copper and aluminum wires in accordance
with
the National
Electrical
Code and local codes and
ordinances.
Improper
connection
of aluminum
house wiring
to copper leads can result in a short
circuit
or fire. Follow the connector
manufacturer
recommended
procedure closely.
This appliance
is manufactured
with a supply wire and
a frame connected
green or bare copper grounding
wire.
DO NOT ground to a gas supply
pipe.
DO NOT connect
to electrical
power supply until
appliance
is permanently
grounded.
Connect
the
ground
wire before turning
on the power.
3
Advertisement
