Cabinet Installation - Frigidaire FEB386CESA Installation Instructions Manual

5. Cabinet Installation
A. 27" Wall Oven
Insert appliance into cutout. Use the screws provided
to fasten the front frame of the appliance to the
cabinet. The mounting holes in the front frame of
appliance may be used as a template to locate the
appliance mounting screw holes.
To fasten the appliance to the cabinet:
1. Line up the 2 mounting holes on the decorative
trim (ventilation) (taped to the oven side panel)
with the lower mounting holes on each side of the
oven frame, below the oven door (see figure 4).
2. Use 2 screws from the miscellaneous parts bag to
secure the decorative trim (ventilation) and
appliance to the cabinetry.
3. Use the remaining 2 screws for mounting the
appliance in the upper two mounting holes on
each side of the oven frame, above the door.
"--.
MOUNTING
REW
DECORATIVE TRIM
VENTILATION)
/
MOUNTING
SCREW
Figure 4
driver (square drive preferred, however a No. 2
Phillips@or Quadrex@ screw driver can also be
used). (If not removed, open the door to remove the
screws, located at the upper end of the side trim).
3. Insert the unit into the cabinet opening. Slide unit
inward leaving 1 3/8" (3.5 cm) clearance between
the oven decorative trim and cabinet. Pull the
armored cable through the hole in the floor and
toward the junction box while moving the appliance
inward. Use the second set of holes in the side frame
of the unit as a guide to find the position of the anti-
tip brackets on the sides of the cabinet opening.
Mark the position of the anti-tip brackets as shown in
Figure 5.
4. Pull out the oven approximately 1 foot (30.5 cm)
away from the cabinet. Reposition each bracket on
the cabinet and drill 1/8" pilot holes. Fasten the
brackets in place using the 2 screws supplied (#10 x
1 I/4"
long).
.
.
If needed, add wood spacers at the anti-tip bracket
locations to reduce the cabinet opening to 28 I/2"
(72.4 cm).
Now push the unit in and against the cabinet, then
attach the unit to the anti-tip brackets using the 2
screws removed earlier from the side frame.
For typical under counter installation of an electric
built-in oven with an electric cooktop above, see
Figure 6.
For typical under counter installation of an electric
built-in oven with a gas cooktop mounted above, see
Figure 7.
4. For typical Under counter installation of an electric
built-in oven with an electric cooktop mounted
above, see Figure 6.
5. For typical under counter installation of an electric
built-in oven with a gas cooktop mounted above,
see Figure 7.
B. 30" Wall Oven
The wall oven can tip when the
door is open. The anti-tip brackets supplied with
the wall oven must be attached to the cabinet
and the appliance to prevent tipping of the wall
oven and injury to persons.
Anti-Tip Brackets Installation Instructions
1. Unpack the wall oven and find the 2 anti-tip
screws included in the literature package. The door
may be removed to facilitate handling (see the
Owner's Guide for instructions).
2. The anti-tip brackets are temporarily installed under
the decorative side trims of the oven when shipped
(see Figure 5). Remove the anti-tip brackets from the
unit side frame using a No. 2 Robertson@ screw
Cutout Dimensions
4 28 1/2" (72.4 cm) Min.* I_
29" (73.7 cm) Max.*
l---f
28 1/16" (71.3 cm) Min.
I/
I_ _1 29 5/8" (75.2 cm)Max. I'Z I 27 1/4"
',101' , , /
l[ll'(718cm) Min"
i___ . _ _ I 28 7/8 "
, / /" (733cm/Max
', / /
Anti-Tip Brackets
I / 22"
[ /(s. s.9cm)
21 1/4" I
54.0 cm)
I
_-Wood Shims(If Needed)Y
* RecommendedCutout Width is 28 1/2" (72.4 cm)
Figure 5
4