GE Monogram ZV1050 Installation Instructions Manual
42" island vent hood
Hide thumbs
Also See for Monogram ZV1050:
- Installation instructions manual (16 pages) ,
- Owner's manual (12 pages) ,
- Use and care manual (14 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GE Monogram ZV1050
Summary of Contents for GE Monogram ZV1050
- Page 1 Installation Instructions 42" Island Vent Hood ZVI050 monogram.com...
- Page 2 Safety Information BEFORE YOU BEGIN _ WARNING: Read these instructions completely and carefully. TO REDUCETHE RISKOF FIRE,ELECTRICALSHOCK OR •Im PO RTANT- save these instructions for l ocal INJURY TO PERSONS,OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the inspector's use.
-
Page 3: Table Of Contents
Design Information CONTENTS Design Information Step 3, Check Installation Hardware .......... Product Dimensions ................Step 4, Mount Template ..............Duct Cover Accessories ..............3, 4 Step S, Install Support Frame ............Determine Installation Height ............Step 6, Secure Wiring ................. Advance Planning Step 7, Size and Install Ductwork .......... -
Page 4: Duct Cover Accessories
9'7" ZX10510SFSS 25-112" to 30" 9'8" ZX10510SFSS DUCT COVER DIMENSIONS 25-112" to 30" 9'9" ZX10510SFSS 25-112" to 30" 9'10" ZX10510SFSS ZV1050 Duct Cover Dimensions 25-112" to 30" 9'11" ZX10510SFSS 25-112" to 30" 10'0" ZX10510SFSS ZVl050 11-112" 12" ZX1059 19" 20"... -
Page 5: Advance Planning
Advance Planning POWER SUPPLY TOOLS AND MATERIALS REQUIRED (not supplied) IM PORTANT- Please read carefully. • Tape measure • Knife AWARN ING: FOR PERSONALSAFETY,THIS • Spirit level APPLIANCEMUSTBE PROPERLY GROUNDED. • Wire cutter • Wire stripper • Wire nuts AVERTISSEMENT : •... -
Page 6: Duct Fittings
Advance Planning Total DUCT FITTINGS Equivalent Quantity Equivalent Used Length Duct Piece Dimensions Length* Round, :1ft. straight (per foot length) 1 ft. 3-1/4" x 12" (per foot Use this chart to compute maximum straight length) permissible lengths for duct runs to outdoors. -
Page 7: Step L, Construct Ceiling Support
Installation Instructions ISTEP 11 CONSTRUCT CEILING SUPPORT Ceiling Plan the location eH°°d Determine the exact location of the vent hood. DUnC_inrgne • Use a plumb bob to check location to be sure countertop/cook- top location below the hood will align exactly. •... -
Page 8: Installation Instructions
Installation Instructions [STEP 1 CONSTRUCT CEILING SUPPORT (cont.) EXAMPLE B 16" Joist -i/4" Instoll Cross-Frumi SpGcing _-gymmetricully About_ Duct/Cooktop Centerline 2x4 Cross- Framing 7-1/4"- Align Duct to Cooktop Center of Cooktop Outline Front of Hood Top View--Ceiling Joists Run Perpendicular to Front of Hood EXAMPLE C 2x4 Cross- ii-i/4"... - Page 9 Installation Instructions 2x4 Min. ISTEP 11CONTINUED Cross-Framing • Arrange cross-framing in the ceiling to suit the existing structure. See examples. - Secure each 2 x 4 block with at least four (4)#10 wood screws, Y' long (not supplied). Use 8 wood screws total for the two supports.
- Page 10 Installation Instructions [STEP 2] REMOVE THE PACKAGING The vent hood is packed separately from the decorative duct cover or accessory covers ZX]O59SFSS or ZXI_O5I_OSFSS. • Remove the frame, cover, parts box and packaging. • Remove junction box cover. • Install strain relief onto junction box cover.
-
Page 11: Step 4, Mount Template
Installation Instructions ISTEP 41 MOUNT TEMPLATE • Align the template with the marks on the ceiling and tape in place. - Be sure the template is oriented correctly, with the front of the hood. • Use a plumb bob to be sure the mounting holes will pro- vide parallel alignment with the countertop below. -
Page 12: Ll Step 6, Secure Wiring
Installation Instructions [STEP 6 SECURE WIRING STEP 7 SIZE AND INSTALL DUCTWORK • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, approximately 6" below the support. _!,:,:,it ;f ;,;, Ceiling iX',', iling Left Side View... -
Page 13: Step 8, Install Decorative Duct Covers
Installation Instructions l STEP81INSTALL DECORATIVE DUCT COVERS Install Screwon i TopDuct EachSide Cover Pretap Bottom DuctCover 2 Screwy Hoes TopDuct '; Cover (One BottomDuct Cover Each Right Side) Side ;Front ..Top Duct Cover Install S top .... Screw in Hole ,.._ Stopi_ ", ofUpper ( Inner) f Screw :_:_ DuctCover... -
Page 14: Step 10 Connect Electrical
Installation Instructions [STEP 11 SLIDE DUCT COVER DOWN STEP 10 CONNECT ELECTRICAL Verify thot power is turned off ot the source. - WA RN ING:,fhouse 2-wire wiring is not with a ground wire, a ground must be provided by the installer. -
Page 15: Step 12 Install Filters, Finalize Installation
Installation Instructions STEP 12 INSTALL FILTERS, FINALIZE INSTALLATION Filter Slots • Tip the filter into the lower slots at the rear of the opening. Lift the filter and pull the knob forward until the filter rests on the slots. • Make sure you have engaged the "Clean Filter Reminder Switch"... - Page 16 ® local service in your area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Applic]nces I Pub. No. 31-14899 General Electric Compong...