GE GLDT696T00SS Installation Instructions Manual
GE GLDT696T00SS Installation Instructions Manual

GE GLDT696T00SS Installation Instructions Manual

Built-in dishwasher
Hide thumbs Also See for GLDT696T00SS:

Advertisement

Available languages

Available languages

#_'" C /_ .........
y._l ¢,(::_::. ' _ , F
.>
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES(800.432.2737} or visit our Website at: GEAppliances.com
In Canada call 1.800.561.3344 o r www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IM PORTAN T- o. or o o,, o orR,n
and ordinances.
• Note to Installer-
Be sure to leave these instructions for the
consumer's and local inspector's use.
• Note to Consumer-
Keep these instructions with your
Owner's Manual for future reference.
• Skill Level - Installation of this dishwasher requires basic
mechanical, electrical and plumbing skills. Proper installation
is the responsibility of the installer. Product failure due to
improper installation
is not covered under the Warranty.
See warranty information.
• Completion Time - 1 to 3 Hours. New installations require
more time than replacement installations.
............
TiiiliilI !
=_:
imagination at work
IMPORTANT- .ho.,...o..or.u..
be installed to allow for future removal from the enclosure
if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
FOR YOUR SAFETY
Read and observe all CAUTIONSand WARNINGS
shown throughout these instructions. While performing
installations
described in this booklet, gloves and either
safety glasses or goggles should be worn.
WARNING
To reduce the risk of electrical shock, fire,
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
ADVERTENCIA
Para reducir el riesgo de descarga
el6ctrica, incendio o lesiones a personas,
el instalador debe asegurarse de qua el
lavaplatos est6 completamente cerrado
en el momenta de la instalaci6n.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
31-30263
05-i0
GE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GLDT696T00SS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GE GLDT696T00SS

  • Page 1 ¢,(::_::. ' _ , F .> Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES(800.432.2737} or visit our Website at: GEAppliances.com In Canada call 1.800.561.3344 o r www.GEAppliances.ca BEFORE YOU BEGIN IMPORTANT- .ho.,...o..or.u.. Read these instructions completely and be installed to allow for future removal from the enclosure carefully.
  • Page 2: Materials You Will Need

    Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8"long to secure dishwasher to underside of countertop (in literature package). 2 Wood Screws MATERIALS YOU WILL NEED: Ferrule, compression nut and 90° EIbow(3/8"NPT external thread on one end, opposite end sized to Wire Nuts (3) fit water supply) Thread...
  • Page 3: Prepare Dishwasher Enclosure

    Installation Preparation PREPARE DISHWASHER ENCLOSURE , The rough cabinet opening must be at least 24"deep and 23- 5/8'%o 24" Wide. The opening should beto 35"max. height. , The dishwasher must be installed so that drain hose is no more than 10feet in length for proper drainage. , The dishwasher must be fully enclosed on the top, Countertop CLEARANCES:When...
  • Page 4: Prepare Electrical Wiring

    Installation Preparation PREPARE ELECTRICAL WIRING WARNING FOR PERSONALSAFETY:Remove house fuse or open circuit breaker before beginning installation. Do not use an 1-1/2" Dia. extension cord or adapter plug with this Hole (Hax.) 'DVERTENCIA 3" from ADVERTENCIAPARASEGURIDAD Cabinet PERSONAL:Quite el fusible o abra el interruptor de circuitos antes de comenzar la instalaci6n.
  • Page 5: Prepare Hot Water Line

    (nsta((ation (nstructions BEFORE YOU BEGIN PREPARE HOT WATER LINE Locate and set aside the package containing .The line may enter from Either side, rear or floor within the 2 phillips head counter top mounting screws shaded area shown in Figure F. 2 additional toekickscrews (located in the .The line may pass through the same hole as the literature).
  • Page 6 Installation Instruction STEP 2 - ADJUST LEVELING LEGS STEP 4 - INSTALL POWER CORD .Hove the dishwasher close to the installation Skip this step if dishwasher will be direct wired. location and lay it on its back. The power cord and connections must comply with the National Electrical Code, Section 422and/or local codes and ordinances.
  • Page 7 Not Push Ag(]inst Line Wiring Front Door P(]nel With Figure 14 Knee. D(]m(]ge to The Door P(]nel Will Occur. Figure 12 .As you proceed, pull the dr(]in hose through the opening under the sink. Stop pushing when the dishw(]sher STEP 7 - INSERT DRAIN HOSE THROUGH is (] few inches forw(]rd of (]dj(]cent c(]binetry.
  • Page 8: Step 9 - Position Dishwasher Under Countertop

    Installation Instructions STEP 9 - POSITION DISHWASHER UNDER COUNTERTOP .Check to be sure that wires are secure under the Reposition Dishwasher dishwasher and not pinched or in contact with door / _ \ by Grasping Both springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped.
  • Page 9 Installation Instructions STEP 11 - SECURE DISHWASHER TO STEP 12 - CONNECT WATER SUPPLY CABINET Connect water supply line to 90 ° elbow. The dishwasher must be secured to the countertop. ,Slide compression nut, then ferrule over end of water line. ,Position the dishwasher so that the tub flange aligns ,Insert water line Into 90 elbow.
  • Page 10: Step 13 - Connect Drain Line

    Installation Instructions DRAIN LINE INSTALLATION STEP 13 - CONNECT DRAIN LINE .Connect drain line to air gap, waste tee or disposer using either previously determined method. FOLLOW ALL LOCAL CODES AND ORDINANCES. The drain hose molded end will fit S/8",3/4"or 1" Method i- Air gap with waste tee or disposer diameter connections on the air gap, waste tee or disposer.
  • Page 11: Step 14- Connect Power Supply

    Installation Instructions STEP 14- CONNECT POWER SUPPLY STEP 15 - PRE-TEST CHECKLIST Review this list after installing your dishwasher to Skip this step if equipped with power cord. ovoid charges for o service call that is not covered Verify that power is turned off at the source. by your warranty.
  • Page 12 Installation Instructions STEP 16 - DISHWASHER TEST Turn on power supply(or plug power cord into outlet, if equipped). Turn on Dishw(]sher Select"Norm(]l w(]sh" progr(]m. Close the door. There will be (] 5 second p(]use, followed by (] 60 second pump-out. Check to be sure th(]t w(]ter enters the dishw(]sher.
  • Page 13 La garantie des appareils Vinstallation d6crite dans ce livret, il faut porter des gants m@nagers de GE ne couvre pas les d@faillances du produit des lunettes de s@curit@. caus@es par une mauvaise installation. Consulter renseignements dans la garantie. AVERTISSEMENT , Dur_e d'installation - 1 6 3 heures.
  • Page 14 Pr6paration pour I'installation Deux vis 5 bois 5 t_te plate cruciforme num6ro 8, v_s sp6ciales a t_tecruciforme de 1,6 cm de long pour bloquer le lave-vaisselle sur le dessous du comptoir (dans la documentation). MATERIAU× NECESSAIRES: Bague, 6crou de compression et coude 5 angle droit ( filetage externe de 3/8 po a une extr6mit6, I'eutre extr6mit6 correspondent 5 I'elimentation d'eeu) Serre-fils...
  • Page 15 Installation Preparation , L'ouverturebruteduplacarddoit_tred'aumoins6Zcmde PREPARER L'ENCEINTE DU LAVE-VAISSELLE profondeur et de 60 6 61 cm de large. L'ouverture doit avoir une hauteur max de 89 cm. , Le lave-vaisselle doit _tre install# de mani@e 6 ce que le Cette portion du tuyau de vidange ne soit pas plus de 3 m de long pour mur ne dolt pas assurer une bonne vidange.
  • Page 16 Preparation pour l'installation - Alimentation lectrique PRI PARATION POUR LE BRANCHEMENT I LECTRIQUE SI_CURITI_ : Autreemplacement possibledela d_clencher le disjoncteur avant de prisede courant commencer l'installation. Avec cet Enlever le fusible du circuit appareil, ne pas utiliser une rallonge ou un adaptateur de prise.
  • Page 17: Avant De Commencer

    Preparation pour Finstallation - Nimentation d'eau chaude PRI PARATION DE L'ALIMENTATION D'EAU , TTENTION: CHAUDE Ouvrir la porte fait basculer le lave- Tuyau d'eau chaude vaisselle vers I'avant. Ne pas ouvrir pas . Le tuyau peut entrer d'un c8t6 ou de I'autre, de I'arri_re ou du la porte avant d'etre pr_t (3installer sol, dans la zone hachur6e montr6e 6 la figure F.
  • Page 18 Installation du lave-vaisselle I_TAPE 2 - RI_GLAGE DES PIEDS DE MISE I_TAPE4 - INSTALLATION DU CORDON NIVEAU D'ALIMENTATION , Rapprocher le lave-vaisselle de I'emplacement Sauter cette 6tape si le lave-vaisselle doit _tre c_bl6 directement. d'installation et le poser sur son dos. Le cordon d'alimentation etles connexions doivent _tre conformes au code 61ectrique national, section 422 et(ou) uux r6glementations et ordonnances en vigueur.
  • Page 19 Installation du lave-vaisselle I_TAPE 8" GLISSER LE LAVE-VAISSELLE _, I_TAPE 6 : MISE EN PLACE DU TUYAU D'EAU ET DES FILS DE LA PIAISON TROIS QUARTS DANS L'OUVERTURE DE L'ARMOIRE . Mettre en place le tuyau d'eau et les ills de la maison sur le sol de I'ouverture, afin d'6viter toute interf@ence avec la base du lave-vaisselle et des divers 616ments sous I k A i1_ l'_...
  • Page 20 Installation du lave-vaisselle I_TAPE 9 - POSITIONNEMENT DU LAVE-VAISSELLE SOUS LE COMPTOIR , V6rifier que les ills sont bloqu6s sous le lave-vaisselle et qu'ils ne sont pas pinc6s ni en contact avec les ressorts de la porte ou avec d'autres pisces du lave-vaisselle.
  • Page 21 Installation du lave-vaisselle I_TAPE 11 - FIXATION DU LAVE-VAISSELLE ETAPE 12 " BRANCHEIENT AU PLACARD L'ALIMENTATION D'EAU Le Iove-vaisselle doit 6tre bloqu6 sur le comptoir. Brancher le tuyau d'alimentation d'eau au coude 5 angle droit. , Positionner le lave-vaisselle de mani@e 5 ce que la bride , Glisser 1'6croude compression et ensuite la bague sur de la cuve s'aligne sur I'avant du cadre du placard.
  • Page 22: Installation Du Tuyau De Vidange

    Installation du lave-vaisselle I_TAPE 13 - RACCORDEMENT DU CONDUIT INSTALLATION DU TUYAU DE VIDANGE DE VIDANGE . Brancher le tuyau de vidange sur le dispositif anti-siphon, OBSERVER TOUTESLESREGLEMENTATIONS E T le raccord en t6 d'6gout ou le broyeur (_d6chets, en ORDONNANCESENVIGUEUR.

Table of Contents