GE PDW8000 Installation Instructions Manual
Built-in dishwashers
Hide thumbs
Also See for PDW8000:
- Owner's manual (28 pages) ,
- Installation instructions manual (16 pages) ,
- Owner's manual (48 pages)
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Installation
Instructions
Built-In Dishwashers
PDW8000, PDW8060
DesignGuide with
Installation Instructions
GEAppliances
Advertisement
Related Manuals for GE PDW8000
Summary of Contents for GE PDW8000
- Page 1 Installation Instructions Built-In Dishwashers PDW8000, PDW8060 DesignGuide with Installation Instructions GEAppliances...
- Page 2 Prepare Hot Water Line ..........Custom Pm_el Dimensions Step ] 2, Pre-Test Check List ........Custom Panels hw PDW8000 ........Step ] 3, Dishwasher Wet Test ........Step 14, Secure Dishwasher to Cabinet or Countertop ........Step 15, Install Toekick ..........
- Page 3 Design Information PRODUCT DIMENSIONS ADVANCE PLANNING • These dishwashers are designed for versatility, adaptable to virtually any installation. • All models have a flfll length door or a modified door to accept a fifll cabinet panel without tile 34" traditional access panel Adjustable...
- Page 4 Installation Preparation MATERIALS YOU WILL NEED: ©G Materials Required for All Installations Screw Type Clamps [] 90° Elbow (3/8"NPT external thread on one end, opposite 90 ° Elbow © end sized to fit water supply) Note: Use new ferrule. Do not use old parts. [] Strain relief for electrical connection [] Thread seal tape Strain Relief...
- Page 5 Installation Preparation PARTS SUPPLIED: Remove hardware accessory other parts or taped fl'om inside to the outside of the dishwasher. Check contents against illustrations to ii'Jsure that parts included. [] 2-piece toekick [] 6 screws (see illustration) [] 2 leveling legs Junction BoxCover [] Junction box cover...
- Page 6 Installation Preparation DRAIN REQUIREMENTS Method 1 - Air Gap with Waste Tee or Disposer • Follow local codes and ordinances. An air gap must be used when the waste tee or disposer connection is less than 18" from the floor. •...
- Page 7 Installation Preparation PREPARE ELECTRICAL WIRING FOR PERSONAL SAFETY: Remove house fllse or open circuit breaker before begimfing installation. Do not use an extension cord or adapter plug with this appliance. POUR ASSURER LA S1_CURIT1_ " Cabinet PERSONNELLE, il flint enlex er le fllsible 2"...
- Page 8 Installation Preparation PREPARE HOT WATER LINE line may enter fl'om either side, rear or floor within the shaded area shown. • The water line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional l-1/2"...
- Page 9 Custom Panel Dimensions CUSTOM PANEL FOR MODELS 3/4" PANEL WITH ZPF675 TRIM KIT PDW8000 on your ctlstom panel size xaries depending installation. Panel kits must be ordered separately. Installation of any custom panel should be completed before the dishwasher is installed.
- Page 10 Installation Instructions lSTEP31 REMOVE ACCESS COVER BEFORE YOU BEGIN: CUSTOM PANEL INSTALLATION: Ifvou intend install custom door panels, (on some models) refer to trim kit installation instructions. Custom panels should be in place bet0re installing tile dishwasher. ISTEP 1] REMOVE PACKAGING Cut tile shipping carton...
- Page 11 Installation Instructions [STEP 5] INSTALL POWER CORD [STEP 7] SLIDE DISHWASHER INTO OPENING SKIP THIS STEP IF DISHWASHER WILL BE DIRECT WIRED DO NOT PUSH AGAINST THE FRONT PANEL WITH • Maxim mn power cord length is 6 ft. KNEES, DAMAGE WILL OCCUR! •...
- Page 12 Installation Instructions [STEP 9] CONNECT DRAIN LINE [STEP 101 CONNECT ELECTRICAL FOLLOW ALL LOCAL CODES AND ORDINANCES. FOR DIRECT WIRE ONLY • The dishwasher is supplied with a 72" long drain hose. (If a power cord with plug is used, plug it into wall...
- Page 13 Installation Instructions I STEP 111 POSITION AND LEVEL THE DISHWASHER • Check to be sure the dishwasher is a(!justed to coiTect DoorRub height is centered in the cutout. OnRight OnLeft • Open and close the door to insure proper operation the door.
- Page 14 Installation Instructions [STEP 14] SECURE DISHWASHER [ STEP 151 INSTALL TOEKICK TO CABINET AND • Loosen depth a(!justment screws inside tile bracket. COUNTERTOP • Slide bracket to proper depth. To maintain position aligmnent, it is rec(nmnended Tighten screws. tile dishwasher be secured to tile countertop •...
- Page 15 Installation Instructions [STEP 16] ADJUST SIDE FILLER STRIPS • Open door fldlv. • Loosen (but do not reinove) screws holding side ti'iI/lS. • A(!just triIll to cover opening gap. Tighten screws. AdjustSideTrim to Meet Cabinetry...
- Page 16 Note: While performing installations described in this book, safety glasses or goggles should be worn. Note: Product improvement is a colltilltlhlg c[lde_wor General Electric. Therefore, materials, appearance specifications sul{iect to change without notice. 0616400 350 Pub.No.31-30545 Dwg.No.203C1559P085 (N.D.318) 11/01...