Table of Contents
Advertisement
Front and Rear Panel Layout
MONO OUT – The Left and Right main Mix outputs are
43
summed together to a monaural signal and sent out this
connector.
EQ IN/OUT – When pressed in, the Amber LED will illu-
44
minate indicating that the Graphic Equalizer is active.
AUX RETURN 2 – This control knob is used to adjust
45
the level of the signal connected to the AUX RETURN 2
inputs.
EQ TO AUX - When pressed in, the onboard Graphic
46
Equalizer is switched from the main mix to the AUX 1
output.
47
SOLO (AUX RETURN 2) - Back-lit LED switch used to
assign the AUX RETURN 2 bus to the SOLO bus.
+48 PHANTOM POWER LED – Indicates that the 48 Volt
48
Phantom Power is on.
49
POWER LED – Indicates the MDR16 is powered up.
50
SOLO LED – Indicates SOLO is selected.
PFL LED – Indicates the SOLO is in PFL (Pre-Fader Level)
51
mode.
52
OUTPUT METER – Twelve-segment display with VU bal-
listics indicates main Mix level.
53
DSP AUX 1 - This control knob is used to adjust the level
of the internal DSP effect in the AUX 1 outputs
54
DSP ON – This push switch is used to engage the
onboard DSP effects.
55
DSP PRE-SET SELECT – Used to switch between the 8
pre-sets of the internal DSP effects processor.
SOLO Switch (3/4 Bus) – Back-lit LED switch used to
56
assign the 3/4 Bus to the SOLO bus.
57
SOLO/PFL Switch – Used to change the operating mode
of the SOLO bus from SOLO to PFL (Pre Fader Listen).
3/4 TO MIX Switch – When engaged, the LED lights and
58
the input channels which are assigned to 3/4 will be
mixed together with the Main Left and Right Outputs.
59
MIX MUTE Switch – When the switch pressed, the red
LED lights indicating the Main Left and Right outputs are
fully attenuated.
SOLO DEFEAT Switch – This global control, back-lit
60
switch is used to disconnect all channels from the SOLO
bus.
MIX L R FADER- Used to control the overall volume of
61
the Left and Right main Mix outputs.
62
62
62
HEADPHONE JACK
HEADPHONE JACK – Connect stereo headphones here.
HEADPHONE JACK – Connect stereo headphones here.
63
C ROOM + HEADPHONE – Adjusts the volume of the
control room speakers or headphones.
SOLO LEVEL – A rotary control knob used to set the
64
overall volume of the SOLO bus.
65
MIX/2TK– Switches between the main Mix and the 2
Track in the Control Room output.
66
OUTPUT 4 FADER – Used to control the overall volume
of the bus 4 mix output.
OUTPUT 3 FADER – Used to control the overall volume
67
of the bus 3 mix output.
68
OUTPUT 2 FADER – Used to control the overall volume
of the bus 2 mix output.
69
OUTPUT 1 FADER – Used to control the overall volume
of the bus 1 mix output.
1/2 TO MIX – When engaged, the LED lights and the
70
input channels which are assigned to 1/2 will be mixed
together with the Main Left and Right Outputs.
SOLO (1/2 Bus) – Back-lit LED switch used to assign the
71
1/2 Bus to the SOLO bus.
This control knob is used to adjust the
72
DSP 3/4 –
level of the internal DSP effect in the Bus 3/4 out-
puts
SOLO (AUX RETURN 1) – Back-lit LED switch used to
73
assign the AUX RETURN 1 to the SOLO bus.
This control knob is used to adjust the
74
DSP 1/2 -
level of the internal DSP effect in the Bus 1/2 out-
puts
DSP PEAK LED – LED light illuminates when the signal
75
sent to the internal DSP is clipped.
76
AUX RETURN 1 Knob – Used to mix in level of the
external effects connected to the Aux RETURN 1 inputs.
3/4 ASSIGN – LED, back-lit switch used to assign the
77
channel to the 3/4 output bus.
78
1/2 ASSIGN (Stereo Channels) – LED, back-lit switch
used to assign the channel to the1/2 output bus.
SOLO Switch (Stereo Channels) – Back-lit LED switch
79
used to assign the channel to the SOLO bus.
�
�
�
����� �����
���� �� �����
REAR PANEL
A
AC ADAPTER INLET
AC ADAPTER INLET – Connect External AC power
AC ADAPTER INLET – Connect External AC power
supply here.
B
POWER – Switches on the MDR16's main power.
C
PHANTOM – Engages the 48-Volt Phantom
power supply to microphone pre-amps.
6
�����
��
��
�
�
�
�
�����
�������
������������������
Hide quick links:
Advertisement
Table of Contents
