The Rear Panel - Blackheart Little Giant 5 112 User Manual

The Rear Panel

VOLTAGE
STICKER
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
DESIGNED FOR CRATE IN USA. MANUFACTURED IN CHINA. FABRIQUE EN CHINE
© 2007 LOUD TECHNOLOGIES INC. "BLACKHEART ENGINEERING" AND "CRATE" ARE
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)
MAINS
100/120VAC 50~60Hz - T2.AL 250V FUSE
WHY ARE YOU SITTING THERE READING THIS STUFF? PLUG IN AND START ROCKING!
FUSE 220/240VAC 50~60Hz - T1.AL 250V FUSE
9
WARNING! Never turn on or use the amplifier without a load or speaker connected to the amplifier.
ALWAYS use a good quality (non-shielded) speaker cable. Never use (shielded) instrument cable.
ALWAYS match the amplifier's speaker output impedance to the impedance of the speaker
that is being used. Use only one type impedance output at a time. If more than one speaker is
connected at the same time, make sure they all have the same impedance rating. Never use
two or more cabinets with different impedance ratings. This will create an unbalanced load.
When using multiple speaker cabinets (with the same impedance rating), match the total load
impedance of the speaker cabinets to the speaker output of the amplifier.
SPEAKER CABINET IMPEDANCE divided by NUMBER OF CABINETS = TOTAL LOAD
4 x 16 ohm cabinets with parallel inputs = 4 ohm load. For this application use 4 ohm output jacks.
2 x 16 ohm cabinets = 8 ohm load. For this application use the 8 ohm speaker jacks.
(If using the internal 16 ohm speaker with an external 16 ohm speaker, connect them both to the 8 ohm jacks.)
1 x 16 ohm cabinet = 16 ohm load. For this application use the 16 ohm speaker jack.
2 x 8 ohm cabinets = 4 ohm load. For this application use the 4 ohm output jacks.
1 x 8 ohm cabinet = 8 ohm load. For this application use the 8 ohm speaker jack.
1 x 4 ohm cabinet = 4 ohm load. For this application use the 4 ohm speaker jack.
9. AC Power Input with Mains Fuse
Assembly: Your amplifier is equipped with a
detachable power cable that plugs into the
IEC Mains socket of the amplifier (located
inside the open hole in the back of the cabi-
net, towards the top). The AC power cord
should only be plugged into a grounded
power outlet that meets all applicable electri-
cal codes and is compatible with the voltage,
power, and frequency requirements stated
on the rear panel of the amplifier. Do not
attempt to defeat the safety ground con-
nection. The AC Mains fuse is located in the
IEC Mains socket and is used to protect the
amplifier from electrical faults. If the fuse
needs to be replaced, please refer to the
correct fuse specifications located on the
back panel of the amplifier. Never bypass the
fuse or replace it with a wrong type or value.
10. 16 OHMS: The 16 ohms speaker output
jack is designated for 16 ohm speaker cabi-
nets only. The Blackheart Little Giant 5 112
Combo is equipped with a Custom Designed
6
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
MANUFACTURING DATE
SERIAL NUMBER
REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND
ICES-003, FOR CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO
THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
POWER CONSUMPTION 45VA
LITTLE GIANT 5 - SINGLE ENDED/CLASS A AMPLIFIER
LOUDSPEAKER OUTPUTS
C US
POWER OUTPUT 5 WATTS RMS
CONNECT SPEAKERS BEFORE USE
16 OHMS 8 OHMS 8 OHMS
WARNING!:
DO NOT OBSTRUCT VENTILATION GRILLES
ATTENTION!: NE PAS OBETRUER LES GRILLES DE VENTILATION
10 11
Eminence Speaker rated at 16 ohms. Be
sure the combo's speaker is plugged into the
16 OHMS jack before the amp is turned on.
NOTE: Use the 8 OHMS and 4 OHMS
speaker outputs if you want to use external
speaker cabinets instead of the built-in 16
ohm Eminence speaker. Unplug the built-
in speaker when using the 8 OHMS or
4 OHMS speaker outputs.
11. 8 OHMS: The two 8 ohms speaker output
jacks are wired in parallel. Use a single jack
when using one 8 ohm speaker cabinet. Use
both speaker jacks when using two 16 ohm
speaker cabinets.
12. 4 OHMS: The two 4 ohms speaker output
jacks are wired in parallel. Use a single jack
when using one 4 ohm speaker cabinet. Use
both speaker jacks when using two 8 ohm
speaker cabinets. If you have four 16 ohm
cabinets with parallel speaker jacks (i.e.,
Blackheart 112 or 412 Cabinet), you can link
all four 16 ohm cabinets in a parallel wiring
configuration, totaling a 4 ohm load.
4 OHMS 4 OHMS
12