Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
For Two-Piece Toilets with Aquameter™ Fill Valve
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a.
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must
be as listed below:
For 4010.010/4310.016 Tanks: A = 254mm (10")
For 4014/4314 Tanks: A = 356mm (14")
For 4010.012/4392.016 and all other Tanks: A = 305mm (12")
FINISHED WALL
A
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A m e r i c a n S t a n d a r d I n c . 2 0 0 4
RENAISSANCE 2241
COMPACT 2149.012, 3505
COLONY 2388 / 2399 / 2359
COLONY AFTON 2329.016
Adjustable Wrench
Flexible Supply Tube
SUPPLY
AS
REQ'D.
FINISHED
FLOOR
Sealant
Tape Measure
Closet Bolts
Carpenters Level
3
CLOSET FLANGE
CLOSET BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ,
and slide into place 6" (152 mm) apart and
parallel to wall.
A
Saniwares
7 30237- 100 R EV. Q
Advertisement
Related Manuals for American Standard COMPACT 3505
Summary of Contents for American Standard COMPACT 3505
-
Page 1: Installation Instructions
For Two-Piece Toilets with Aquameter™ Fill Valve Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes... - Page 2 WAX RING SEALANT INSTALL WAX SEAL Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around base flange. BOLT CAP CLOSET FLANGE CLOSET BOLT WASHER...
- Page 3 WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite).
-
Page 4: Troubleshooting Guide
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address: In the United States: American Standard Inc. P.O. Box 6820 Piscataway, New Jersey 08855...