Drolet CLASSIC EPA WOOD STOVE Owner's Manual
  1. Manuals
  2. Brands
  3. Drolet Manuals
  4. Wood stove
  5. CLASSIC EPA WOOD STOVE
  6. Owner's manual

Drolet CLASSIC EPA WOOD STOVE Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Manufactured by : STOVE BUILDER INTERNATIONAL INC.
250, de Copenhague, Saint-Augustin-de-Desmaures (Quebec), Canada G3A 2H3
This manual is available for free download on the manufacturer's web site. It is a copyrighted
document. Re-sale is strictly prohibited. The manufacturer may update this manual from time
to time and cannot be responsible for problems, injuries, or damages arising out of the use of
information contained in any manual obtained from unauthorized sources.
READ AND KEEP THIS MANUAL FOR REFERENCE
Printed in Canada
OWNER'S MANUAL
CLASSIC EPA WOOD STOVE
Tel: (418) 878-3040
Fax: (418) 878-3001
www.drolet.ca
US ENVIRONMENTAL PROTECTION
AGENCY PHASE II CERTIFIED WOOD
STOVE
Verified and/or tested following
ULC S627 and UL 1482 Standards
by:
45145A
14-04-2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CLASSIC EPA WOOD STOVE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Drolet CLASSIC EPA WOOD STOVE

Summary of Contents for Drolet CLASSIC EPA WOOD STOVE

  • Page 1 OWNER’S MANUAL CLASSIC EPA WOOD STOVE US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOOD STOVE Verified and/or tested following ULC S627 and UL 1482 Standards Manufactured by : STOVE BUILDER INTERNATIONAL INC. 250, de Copenhague, Saint-Augustin-de-Desmaures (Quebec), Canada G3A 2H3...
  • Page 2 Keep your sales invoice. We also recommend that you register your warranty online at www.drolet.ca Registering your warranty online will help us track rapidly the information we need on your stove.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS TECHNICAL SPECIFICATIONS ..........................4 TIPS ON WOOD HEATING ........................... 5 SECTION 1.0 - INSTALLATION ........................... 6 GENERAL INSTALLATION ..............................6 POSITIONING THE STOVE ............................... 6 CLEARANCES TO COMBUSTIBLES AND FLOOR PROTECTOR .................... 7 SECTION 2.0 CHIMNEY (FLUE SYSTEM) ...................... 14 DEFINITIONS ................................
  • Page 4 SECTION 4.0 MAINTENANCE ........................37 CLEANING AND PAINTING YOUR STOVE ........................37 GLASS ..................................37 GASKETING .................................. 37 ASH REMOVAL USING THE ASH DRAWER ........................38 CHIMNEY (FLUE) CLEANING ............................39 DROLET LIMITED LIFETIME WARRANTY ....................40...

  • Page 5: Technical Specifications

    TECHNICAL SPECIFICATIONS Recommended Surface 900 to 1 800 ft Heating Capacity* : E.P.A : 45 000 BTU/h Real : 70 000 BTU/h Optimum efficiency : 6.9 g/hr. Average emissions (EPA): Paint finish : Metallic black 6” (152 mm) Flue outlet (spigot) diameter : 19’’...

  • Page 6: Tips On Wood Heating

     The chimney is the engine that drives the wood-heating system. Use a chimney that is UL- listed, with an inner diameter to match the stove’s outlet collar (6” for all Drolet wood stoves);  Try to run the chimney inside the building for as much length as you can. A tall and warm chimney will produce a good draft;...

  • Page 7: Section 1.0 - Installation

    SECTION 1.0 - INSTALLATION When installed and operated as described in these instructions, the Classic EPA wood stove is suitable for use as a freestanding wood stove in residential installations. The Classic EPA wood stove is not intended for installation in a bedroom or a mobile home.

  • Page 8: Clearances To Combustibles And Floor Protector

    CLEARANCES TO COMBUSTIBLES AND FLOOR PROTECTOR To install your appliance correctly, it is extremely important to respect all clearances to any combustibles as indicated on your stove’s certification label. Clearances to combustible materials (See figure 1.3 to match each letter to a clearance) CLEARANCES (SINGLE WALL PIPE) CANADA 18"...
  • Page 9 FIGURE 1.3 Clearances to combustible materials and floor protection...
  • Page 10 Floor protector If the stove is to be installed on top of a combustible floor, it must be guarded by a non combustible material as shown on figure 1.3 (see the dotted line area). FLOOR PROTECTOR* CANADA 8’’ (205 mm) – Note 1 N/A (Canada only) 8’’...
  • Page 11 Reducing Clearances With Shielding TYPE OF PROTECTION Sides and Rear/Back Sheet metal, a minimum of 0,024" (0,61mm) spaced out at least 1" (25mm) by non-combustible spacers (see graphic 2). Ceramic tiles, or an equivalent non-combustible material on fire-proof supports spaced out at least 1" (25 mm) by non- combustible spacers (see graphic 3).
  • Page 12 Graphic 1 A- Minimum clearance required between the appliance and an unshielded combustible ceiling. B- 20 in. (500 mm) minimum; C- 1 in. (25 mm) minimum; D- Between 1 in. and 3 in. (25 mm and 75 mm); E- 3 in.(75 mm) minimum; F- 18 in.
  • Page 13 Graphic 2 A- 1 in.(25 mm) minimum; 1- Combustible wall; 2- Non-combustible spacers; 3- 0.024’’ (0.61mm) sheet metal. Graphic 3 A- 1 in. (25 mm) minimum; 1- Combustible wall; 2- Non-combustible spacers; 3- Non-combustible support; 4- Ceramic tile or non-combustible material. Graphic 4 A- 1 in.
  • Page 14 Graphic 5 A- 1 in. (25 mm) minimum; 1- Combustible wall; 2- Non-combustible spacers; 3- Brick. Graphique 6 A- 1 in. (25 mm) minimum; 1- Combustible wall; 2- Non-combustible spacers; 3- 0.024’’ (0.61 mm) thick sheet metal; 4- Brick.

  • Page 15: Section 2.0 Chimney (Flue System)

    SECTION 2.0 CHIMNEY (FLUE SYSTEM) DEFINITIONS For clarity, the following definitions should be used with respect to these instructions: A chimney system consists of a connector off the top of the stove, and a chimne , which attaches to the connector and terminates outside the house. A chimney can be a masonry chimney (of masonry construction with an inside liner), or a factory built chimney.
  • Page 16 If you are using a masonry chimney, it is important that it be built in compliance with the specifications of the Building Code. It must be lined with fire clay bricks, or clay tiles, sealed together with fire cement, or have a listed solid fuel burning stainless steel liner.

  • Page 17: Step By Step Installation Of Your Factory-Built Chimney

    FIGURE 2.2 Minimum Height of the Chimney 2.2.1 Step by step installation of your factory-built chimney The way to install your chimney may vary from one chimney manufacturer to another. The instructions contained in this manual are based on the recommendations of chimney manufacturers whose products are sold at many North American retailers of wood stoves and related heating accessories.
  • Page 18 Typical installation through the wall FIGURE 2.2.1 (A) Typical installation through the wall 1- Start by positioning your stove where you would like it to go, taking into account the minimum clearances to combustible material. You will then be able to determine where the chimney will pass through the wall.
  • Page 19 2- Once the opening completed, you need to frame in the area to allow for the installation of a wall thimble. A wall thimble is not required for installations through concrete walls. 3- You must first secure the wall thimble into the exterior wall surface. Then, do the same inside and fasten the trim plate.
  • Page 20 5- You can now install the wall support. Simply slide the wall support up to the tee, ensuring that the adapter on the support engages with the female coupler on the bottom of the tee. When the wall support is level and properly positioned, you can use lag bolts to secure it into the wall studs.
  • Page 21 8- Finally, twist on your rain cap and you can head back inside. 9- You are now ready to connect your chimney to your stove. Simply install the inter-connecting stove pipe between the stove pipe adapter and the stove. You can follow the instructions in the following section (section 2.3) of this manual called «...
  • Page 22 Typical installation through the ceiling FIGURE 2.2.1 (B) Typical Installation Through the Ceiling 1- Place your stove where you would like it located and use a plumb line to mark the ceiling directly above your stove flue. You will probably have to adjust this position slightly to ensure that your chimney will run between the joists.
  • Page 23 2- Before you install the ceiling support, you need to frame the area. 3- To install the ceiling support, just slide the assembly into the framed opening from below. Once you ensure that the finishing plate is flush with the underside of the ceiling and assembly is level, secure it with screws.
  • Page 24 6- Now, you can add additional chimney sections. Continue adding chimney lengths until a height of about 2 feet below the next ceiling level. An attic insulation shield must be installed where a chimney passes from a lower living space into an upper living space or attic space. It is designed to keep insulation materials away from the chimney.

  • Page 25: Typical Installation Through An Existing Masonry Chimney

    9- You are now ready to connect your chimney to your stove. Simply install the inter-connecting stove pipe between the stove pipe adapter and the stove. You can follow the instructions in the following section (section 2.3) of this manual called « CHIMNEY CONNECTOR». 2.2.2 Typical installation through an existing masonry chimney You can also install your stove using your existing masonry chimney.
  • Page 26 FIGURE 2.2.2 (B) Factory Built Thimble...
  • Page 27 FIGURE 2.2.2 (C) Brick Thimble...

  • Page 28: Chimney Connector

    CHIMNEY CONNECTOR Your chimney connector (commonly called stove pipe) and chimney must have the same diameter as the stove’s exhaust outlet. The stove pipe must be made of aluminized or cold roll steel with a minimum 24- gauge thickness (0.021" or 0.53 mm). It is strictly forbidden to use galvanized steel. The following recommendations may be useful for the installation of your chimney connector: Your chimney connector should be assembled in such a way that the male end (crimped) faces down to prevent creosote dripping outside the joints.
  • Page 29 FIGURE 2.3 (B) Minimum Slope We recommend that you use Avoid 90 degree eblows two 45 degree elbows instead...

  • Page 30: Draft

    DRAFT Your Classic EPA stove’s performance will be optimised if it is installed with a chimney (flue) system that provides an adequate draft. The draft is the force that moves air from the appliance up through the chimney and is predominantly affected by the height and diameter of the chimney, as well as the stack temperatures of the stove.

  • Page 31: The Advantage Of Installing A Blower (Fan)

    THE ADVANTAGE OF INSTALLING A BLOWER (FAN) A blower is installed at the back of your Classic EPA wood stove. The blower should be used if you wish to redistribute into a room the heat trapped at the back of your stove. By forcing hot air toward the front, the...

  • Page 32: Operation

    SECTION 3.0 OPERATION Keep these instructions for future reference. WARNING: ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN WRITING BY THE TESTING CSA B365 ( ANSI NFPA 211 (USA). AUTHORITY IS CONSIDERED AS BREACHING CANADA DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR REKINDLE THE FIRE DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHEN IT IS OPERATING DO NOT STORE FUEL WITHIN HEATER INSTALLATION CLEARANCES...
  • Page 33 Even though your Drolet has been specifically designed and tested to prevent smoke spillage, always open the door slowly as this will minimise the likelihood of smoke spillage or a back draft of flame or smoke into the room. Never use gasoline type lantern fuel, kerosene, solvents, charcoal lighter fluid, or inflammable liquids to start or "refresh"...

  • Page 34: Fuel

    Fuel for the stove must not be stored closer than the required clearances to combustibles (heat sensitive materials). NEVER STORE WOOD IN THE ASH PAN COMPARTMENT. Your Drolet stove is designed to burn . Do not burn coal, charcoal, or trash in the unit. Highly WOOD ONLY flammable items such as trash may ignite creosote in the chimney (flue), resulting in a chimney fire.

  • Page 35: The Use Of Manufactured Logs

    Decorative fireplaces generally have larger, cooler, and less air-tight fireboxes. Your Drolet stove, on the other hand, has a smaller, completely sealed firebox which attains much higher temperatures. It is therefore not designed to support excessive heat caused by the addition of chemicals in manufactured logs.

  • Page 36: Maintaining The Fire

    Your Drolet stove will work best if a thick bed of hot embers is maintained in the bottom of the firebox, and a minimum of two large pieces of seasoned fuel are added. Combustion efficiency is largely related to establishing a hot ember bed, and hot firebox temperatures.

  • Page 37: Fan (Blower) Operation

    FAN (BLOWER) OPERATION Allow the stove to reach operating temperature (approximately one hour), before turning on the fan. The increased airflow from the fan will cool the firebox and affect the start-up combustion efficiency if the fan is turned on too quick. It is possible to have an automatic activation of the blower with the installation of a basic thermodisc kit AC05530 or a quick connect thermodisc kit AC02055.

  • Page 38: Maintenance

    Carefully clean the gasket groove, apply a high temperature silicone sold for this purpose, and install the new gasket. Use only the genuine Drolet gasket. You may light up your stove again approximately 24 hours after having completed this operation.

  • Page 39: Ash Removal Using The Ash Drawer

    ASH REMOVAL USING THE ASH DRAWER AUTION ASHES CAN START FIRES EVEN AFTER SEVERAL DAYS OF INACTIVITY EVER DISPOSE OF ASHES IN A COMBUSTIBLE CONTAINER EMOVE ASHES WHEN THE STOVE AND ASHES ARE COLD Whenever the ashes get 3 – 4” (76 – 102 mm) deep in the firebox, they should be emptied into the ash drawer, using the following instructions: Make sure the fire is out, and the stove is cold.

  • Page 40: Chimney (Flue) Cleaning

    If creosote has accumulated, it should be removed to reduce the risk of a chimney fire. Call a professional chimney sweep, or go to your local Drolet dealer, purchase a chimney brush, and have the chimney cleaned.

  • Page 41: Drolet Limited Lifetime Warranty

    Firebrick *Pictures required Shall your unit or a components be defective, contact immediately your DROLET dealer. Prior to your call make sure you have the following information necessary to your warranty claim treatment: Your name, address and telephone number;...

Table of Contents