WOOD HEATING ...3 THE CONTROLLED COMBUSTION WOOD STOVE ASSEMBLING THE STOVE INSTALLING THE FIREBRICKS INSTALLATION OF YOUR DROLET WOOD STOVE POSITIONING THE STOVE ...6 FLOOR PROTECTION ...6 CLEARANCES TO COMBUSTIBLE MATERIALS...7 INSTALLATION OF A HEAT RADIATION SHIELD ...8 STEP BY STEP INSTALLATION OF YOUR CHIMNEY ...9 COUPLINGS...15...
The wood will burn slowly if the wood stove draught keys are adjusted in order to reduce the oxygen supply in the combustion chamber to minimum; on the other hand, wood will burn quickly if the draught keys are...
ASSEMBLING THE STOVE Note: This section applies to models Compak, CS1200, ML, Little Sawman, RC and Nordic only. 1- Mount the 4 legs using 2 screws per leg. 3- Install the heat shield between the front legs, just above the leg supports.
Important: A wood stove must never be installed in a hallway or near a staircase, since it may block the way in case of fire or fail to respect required clearance. The wood stove must not be hooked up to a hot air distribution system since an excessive accumulation of heat may occur.
CLEARANCES TO COMBUSTIBLE MATERIALS It is of utmost importance that the clearances to combustible material mentioned on your wood stove certification plate be scrupulously respected upon installation. Model Back Wall Baron 1880sp 18" / 610 mm Baron 2000sp 24" / 610 mm Baron 1880sp 15"...
INSTALLATION OF A HEAT RADIATION SHIELD Following the installation of a heat radiation shield, the clearances mentioned on the stove certification plate may be reduced as stated in the following table. TYPE OF PROTECTION Minimal requirements: 0,013" (0,33 mm) sheet metal with 1"...
CHIMNEY Your wood stove may be hooked up with a prefabricated or masonry chimney. If you are using a prefab chimney, it must comply with S-629 standards; therefore it must be approved for up to 2100 extremely important that it be installed according to the manufacturer's specifications.
Page 10
A 90 elbow 1- Start by positioning your stove where you would like it to go, taking into account the minimum clearances to combustible material. You will then be able to determine where the chimney will pass through the wall. You will probably have to adjust the stove position slightly to ensure that your chimney will run between the studs.
Page 11
The chimney must extend at least 3 inches into the living space where it attaches to the stove pipe. 5- You can now install the wall support. Simply slide the wall support up to the tee, ensuring that the adapter on the support engages with the female coupler on the bottom of the tee.
Page 12
CEILING SUPPORT SYSTEM If your chimney must rise inside the house and go through the ceiling, you need to connect it to your stove at the ceiling level. For this type of installation, the following items are normally required : Chimney •...
Page 13
Suitable lengths of stove pipe 1- Place your stove where you would like it located and use a plumb line to mark the ceiling directly above your stove flue. You will probably have to adjust this position slightly to ensure that your chimney will run between the joists.
Page 14
Make sure that the male coupler is pointing upwards, as indicated by the arrow on the chimney label. 5- Then, from beneath the support, insert the stove pipe adapter and twist-lock it into place. 6- Now, you can add additional chimney sections. Continue adding chimney lengths until a height of about 2 fet below the next ceiling level.
Furthermore, installation of a draught damper is not recommended. Indeed, with a controlled combustion wood stove, the draught is regulated upon intake of the combustion air in the stove and not at the exhaust. The connectors must not go through a ceiling, a storage area, a floor, or any other combustible partition.
Then attach the unit to the floor using the two screws provided for this purpose AIR CIRCULATION SYSTEM In order to improve air circulation in the room where the wood stove is installed, certain options are available for specific stove models.
The baffle brick will eventually need to be replaced. How long it will take depends on how often you use your stove. It is very important that you do not postpone the replacement of the baffle brick when you see that it starts to disintegrate.
This point cannot be overstressed enough; the vast majority of the problems related to the operation of a wood stove is caused by the fact that the wood used was too damp or had dried in poor conditions.
Make sure that the chimney and flue pipe are well installed according to specifications. Respect all clearances to combustibles and floor protection according to the unit you have chosen. If you are not sure that your installation is adequate, do not hesitate to contact your Drolet dealer. IGNITION The installation of a log cradle is NOT RECOMMENDED in your DROLET wood stove.
Page 21
In summary, it is very easy to operate your wood stove and you can prevent all potential problems by following these recommendations: Select a stove of adequate size: selecting a stove that is too big for the area to be heated is a common mistake;...
- It is possible to give your wood stove a brand new look by repainting it with a 1200° F (649 resistant paint. For this purpose, simply rub the surface with fine sand paper #180. The closer to the metal you go, the tougher the paint coat will be.
PROCEDURES IN CASE OF FIRE IN CASE OF FIRE: • POSITION THE AIR INTAKE OF THE STOVE AT THE MINIMUM TO DEPRIVE IT FROM OXYGEN. • CALL IMMEDIATELY THE FIRE DEPARTMENT.
The word “draft” refers to the hot air movement that circulates in your stove’s exhaust system, moving from the stove to the outside of the house, and carrying with it the combustion residues. The draft is a natural phenomenon. Hot air weights less than cold air, causing it to rise. This is why the higher the temperature in the exhaust system, the stronger the draft.
Page 25
DRAWING #1 shows a stove functioning under normal and adequate conditions. Heat rises to the upper floors and the room where the stove is located has an adequate supply of oxygen. The chimney draft is sufficient and the combustion gases are evacuated normally through the exhaust system.
Page 26
DRAWING #2 DRAWING #2 shows the effect of a cold chimney. Cold air creates a reverse draft (negative pressure), which causes smoking problems. This phenomenon is amplified by the fact that heat rises, which creates a draft from the basement of the house to the upper floors (“chimney stack effect”).
Page 27
DRAWING #3 DRAWING #3 shows the effect of negative pressure caused by an air-moving device inside the house. In the example above, the range hood draws air from inside the house, which is replaced by air coming from the chimney. The result is a smoking problem.
Page 28
DRAWING #4 DRAWING #4 shows the negative pressure effect caused by wind, influenced by nearby structures such as a building.
Page 29
DRAWING #5 DRAWING #5 shows the negative pressure effect that can be caused by wind, influenced by nearby structures such as a tree.
There are different sizes of firebricks. Most stores will sell firebricks with a dimension of 4,5”X9”X1,25”. These firebricks are adequate for many stoves, but will not fit on all Drolet units. It is preferable that you visit our parts section in order to clearly identify the type of firebrick that you need. Some models, like the HT1200, HT2000, Sawman, Vision XL, and Royal Comfort have some larger, non-standard firebricks that are only available on special order.
Paint, refractory bricks, gasket, blower, thermal switch (thermodisc) and rheostat Gold plating (tarnishing) Shall your unit or a components be defective, contact immediately your Drolet dealer. Prior to your call, make sure you have the following information necessary to your warranty claim treatment: •...