Advertisement
Quick Links
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
p/n 305101 Rev. (-)
Model RCP-300
IMPORTANT: DO NOT DISCARD THIS MANUAL
OPERATION MANUAL
RCP-Series
DROP-IN
REFRIGERATED
COLD PANS
RCP-100
RCP-200
RCP-300
RCP-400
RCP-500
RCP-600
INSTALLATION
M405 022103 cps
405
MODELS
RCP-7100
RCP-7200
RCP-7300
RCP-7400
RCP-7500
RCP-7600
Includes
USE & CARE
Advertisement
Related Manuals for Wells RCP-100
Summary of Contents for Wells RCP-100
- Page 1 Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
- Page 2 Seller’s obligation under this warranty is limited to the one year from the date of original installation or 18 months repair of defects without charge by a Wells Mfg. Co. factory from the date of shipment from our factory, whichever...
- Page 3 PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
- Page 4 FEATURES & OPERATING CONTROLS NOTE: This is a general arrangement drawing only. Actual component positions may vary between units.
-
Page 5: Agency Listing Information
This appliance is made in the USA. Unless otherwise noted, this appliance has American sizes on all hardware. AGENCY LISTING INFORMATION Models RCP-100 thru -600 have been evaluated by NSF International for sanitation requirements and not performance tested for potentially hazardous foods. - Page 6 INSTALLATION NOTE: DO NOT discard UNPACKING & INSPECTION the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
- Page 7 This must be plugged into a of tools. Failure to properly grounded matching receptacle. follow this warning can b. RCP-100 thru -600 and RCP-7100 thru -7400 are equipped result in severe electrical with a NEMA 5-15P plug and require a matching NEMA 5-15R shock.
- Page 8 OPERATION CAUTION: OPERATION NOTES Electrical Shock 1. Never place food directly in cold pans. Always use insets or food Hazard pans. DO NOT splash or pour water 2. Use only pre-chilled products. Stir product occasionally to maintain onto control panel or wiring. chilled temperatures and prevent bottom freezing.
- Page 9 CLEANING INSTRUCTIONS PREPARATIONS: Turn POWER SWITCH OFF. Unplug unit or CAUTION: disconnect from electric power. Electrical Shock Allow unit to defrost before proceeding. Hazard Remove any insets, pans and/or adapter tops ( if DO NOT splash or pour water used). Drain water from tank. onto control panel or wiring.
-
Page 10: Maintenance Instructions
MAINTENANCE INSTRUCTIONS CONDENSER COIL CLEANING INSTRUCTIONS CAUTION: Personal Injury The condenser coil must be kept clean to allow adequate air flow for Hazard proper heat dissipation. Recommend this procedure be performed Disconnect appliance from monthly. electrical power before 1. Turn POWER SWITCH OFF. Disconnect unit from electrical cleaning condenser coil. - Page 11 Cleansers containing ammonia will attack the surface and allow the stainless steel to rust. 2. Use the proper tools in the proper way to clean your Wells cold pan: a. Soft cloth and plastic scouring pads are safe to use on stainless steel surfaces.
- Page 12 MAINTENANCE INSTRUCTIONS (continued) TEMPERATURE ADJUSTMENT IMPORTANT: DO NOT adjust the differential RCP-100 thru RCP-600 settings of the refrigeration system. Field adjustments of 1. The temperature has been preset at the factory to meet most the differential settings must applications. be made by qualified refrigeration personnel only.
- Page 13 MAINTENANCE INSTRUCTIONS (continued) 3. Press the SET key again to access the differential. The LCD will IMPORTANT: DO NOT adjust the differential display the current differential, and the DIF1 annunciator will blink settings of the refrigeration off and on to indicate that control is in the differential mode. system.
-
Page 14: Troubleshooting Suggestions
Set to desired temperature Condenser cooling louvers or coil Clean condenser louvers and/or plugged coil Refrigerant level low Contact Authorized Wells Service Agency for repairs Internal damage Contact Authorized Wells Service Agency for repairs NSF-7 operation using wrong rail For holding critical foods, pan... -
Page 15: Customer Service Data
ADAPTER BAR FOR 12" X 20" PANS 22106 filters. PERFORATED BOTTOM PLATE STRAINER For factory authorized FOR RCP-100 and RCP-7100 (1 PC) 22107 service, or to order factory PERFORATED BOTTOM PLATE STRAINER authorized replacement FOR RCP-200 and RCP-7200 (1 PC)