Page 1
Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
The for information and other details concerning warranty. prices charged by Wells Bloomfield for its products are SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS Resetting of safety thermostats, circuit breakers, over cleaning schedules, are customer responsibility.
Page 3
ACCESSORY PARTS & SERVICE DATA INTRODUCTION Thank you for purchasing this Wells Bloomfield appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments WARNING: only, and is intended to hold pre-chilled prepared food for human ELECTRIC consumption. No other use is recommended or authorized by the SHOCK HAZARD manufacturer or its agents. All servicing requiring Operators of this appliance must be familiar with the appliance use, access to non-insulated...
AGENCY LISTING INFORMATION The RCP-7200SL thru RCP-7400SL are performance tested to NSF STD 2 Standard 7 for storage of potentially hazardous foods. These units STD 7 meet NSF Standard 7 only when pan rails are installed in the lowest position, otherwise it meets NSF Standard 2.
INSTALLATION UNPACKING & INSPECTION NOTE: DO NOT discard the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
INSTALLATION ELECTRICAL INSTALLATION WARNING: ELECTRIC 1. Refer to the nameplate. Verify the electrical service power. SHOCK HAZARD Voltage and phase must match the nameplate specifications. All servicing requiring Wiring the unit to the wrong voltage can severely damage the unit, access to non-insulated or cause a significant decrease in performance.
INSTALLATION IMPORTANT: PLUMBING INSTALLATION Plumbing connections must Install 1" drain valve (provided by others) on unit drain. Plumb to an be made in compliance with appropriate waste as required by local plumbing and sanitation all Federal, State and Local ordinances. Consult local codes for approved drain configurations. Codes and Ordinances.
Perforated bottom strainer plates are optional and must be ordered separately. hold REFRIGERATED PRE-CHILLED product at 4. Reminder: only models RCP-7200SL thru RCP-7400SL are NSF-7 listed for use with potentially hazardous foods. RCP-200SL thru serving temperature. RCP-400SL are NSF-2 listed.
CLEANING INSTRUCTIONS PREPARATIONS: Turn POWER SWITCH OFF. Unplug unit or CAUTION: disconnect from electric power. ELECTRIC SHOCK Allow unit to defrost before proceeding. HAZARD Remove any insets, pans and/or adapter tops ( if used). Drain water from tank. DO NOT splash or pour water onto control panel or wiring.
MAINTENANCE INSTRUCTIONS CONDENSER COIL CLEANING INSTRUCTIONS CAUTION: PERSONAL The condenser coil must be kept clean to allow adequate air flow for INJURY HAZARD proper heat dissipation. Recommend this procedure be performed Disconnect appliance from monthly. electrical power before 1. Turn POWER SWITCH OFF. Disconnect unit from electrical cleaning condenser coil.
Page 13
MAINTENANCE INSTRUCTIONS CAUTION: PERSONAL INJURY HAZARD Disconnect appliance from electrical power before cleaning. Wells refrigerated cold pans are constructed of high quality stainless steel. As long as the stainless steel surface is intact, the equipment will not rust or corrode.
3. Normal temperature setting would be 28ºF. The temperature setting of the NSF-7 Refrigerated Cold Pan RCP-7200SL thru RCP-7400SL has been pre-set at the factory to meet most The LCD Display provides a readout of the sensor temperature applications.
Page 15
OPERATING INSTRUCTIONS IMPORTANT: 3. Press the SET key again to access the differential. The LCD will DO NOT adjust the differential display the current differential, and the DIF1 annunciator will blink settings of the refrigeration off and on to indicate that control is in the differential mode. system.
FOR RCP-300 (2 PC) 5O-22109 service agency, or call: PERFORATED BOTTOM PLATE STRAINER FOR RCP-400 (2 PC) 5O-22110 Wells Bloomfield, LLC PAN RAIL FOR RCP-7200SL 5O-22697 10 Sunnen Dr., PAN RAIL FOR RCP-7300SL 5O-22698 St. Louis MO 63143 USA PAN RAIL FOR RCP-7400SL 5O-22699 Service Dept.
Page 20
WELLS BLOOMFIELD, LLC 10 Sunnen Dr., St. Louis, MO 63143 telephone: 314-678-6314 fax: 314-781-2714 www.wellsbloomfield.com...