Related Manuals for Hoover Bagless Upright
Summary of Contents for Hoover Bagless Upright
- Page 1 HOOVER Owner’s Manual ® Bagless Upright ENGLISH pp.1-13 ESPAÑOL pág. 14-21 ™ with Twin Chamber System FRANÇAIS p. 22-29 Read this manual before operating the cleaner www.hoover.com...
-
Page 2: Table Of Contents
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dro p p e d ,d a m age d , left outdoors , or dropped into water, take it to a Hoover Fa c t o ry Service Center or Au t h o r i zed Hoover Warranty Service Dealer (Depot). -
Page 3: Assembling Cleaner
(U.S. only) 1-330-499-9499 to speak with a representative in our Consumer Response Center Visit us on-line at www.hoover.com to find the service outlet nearest you (click on the “Service” button). C a rton contents Remove all parts from carton and identify each item shown. - Page 4 Step 1 Assemble handle Note: The green or white switch With dirt cup toward the front, lock (A) near the ON/OFF switch on slide assembly down onto the the back of the dirt cup assembly, extension on cleaner base. Attaching dirt cup helps in assembling your cleaner.
-
Page 5: How To Use
Avoid tipping cleaner or setting it on furniture, fringed area rugs, or carpeted stairs during tool use. Your bagless upright is Position extension wand (E) and Remove green or white switch lock now assembled and place crevice wand (F) inside exten- (A) in back of the cleaner. -
Page 6: Upright Cleaner
Handle positions Transporting cleaner ON-OFF switch To move your cleaner from room to The handle of your cleaner has three To turn cleaner ON, depress switch (A) positions; upright for storage and when room, put handle in upright position, tilt t o w a rd front. -
Page 7: Cleaning Tools
2-10 Cleaning tools Tools allow you to clean surfaces above the floor and reach hard to clean areas. Use tools with the cleaner handle in upright position. This will ensure that the nozzle is lifted off the floor slightly. C AU T I O N : Agitator continues to ro t a t e while cleaner handle is in upright p o s i t i o n . -
Page 8: Cleaning Hepa Filter
While the cleaner is in operation, the pre - 3. Maintenance filter will stop larger debris from entering the HEPA cartridge filter chamber. This Familiarize yourself with these home l a rger debris will be seen collecting in the maintenance tasks as proper use and left side of the dirt cup. -
Page 9: Replacing Final Filter
3-10 It is recommended that the HEPA car- Grasp end of HEPA cartridge filter and To re-assemble filter assembly, place gently pull it away from pre-filter. tridge filter be cleaned by tapping either large knob of HEPA cartridge filter in Remove cartridge from assembly. -
Page 10: Replacing Belt
Headlight 3-16 3-15 What to buy This cleaner uses a 12 volt, wedge base type 912 bulb, Hoover part No. 27313101. How to replace Disconnect cleaner from electrical out- let. Installing bulb and reposition- Removing hood ing hood Place handle in low position. -
Page 11: Lubrication
(4) Phillips head screws (Fig 3-22). Lubrication 4. When cleaner is unplugged and Do not send your cleaner to The Hoover the motor cools for 30 minutes, the Company in North Canton for service, this will only result in delay. -
Page 12: If You Have A Problem
Hoover Cleaning Per- of dirt cup formance problem Possible cause This Hoover Cleaning Performance Sys- Possible solution If a minor problem occurs, it usually can tem is for comparing the relative pro- • Dirt cup not completely latched be solved quite easily when the cause is gressive performance of Hoover •... -
Page 13: Clearing Blockages
The Hoover Company on-line at www.hoover.com This warranty does not cover pick up, delivery, or house calls; however, if you mail your appliance to a Hoover Factory Service Center for warranty service, transportation will be paid one way. Removing duct cover While this warranty gives you specific 2.