Removing The Collected Water - Heat Controller R-410A Owner's Manual

Heat Controller, Inc.
OPERATING THE UNIT

Removing the collected water

fitting is placed inside the Styrofoam base packaging of the Unit.
There are two ways to remove collected water.
• Locate and remove these items before operating the unit or dispose of packaging materials.
1. Use the bucket
OPERATING THE UNIT
When the bucket is full, the unit will automatically stop
running, the unit will beep 8 times and and the Full
Removing the collected water
indicator light will flash, the digital display shows P2 .
Slowly pull out the bucket. Grip the left and right
There are two ways to remove collected water.
handles securely, and carefully pull out straight so
1. Use the bucket
water does not spill. Do not put the tank on the floor
When the bucket is full, the unit will automatically stop
because the bottom of the bucket is uneven. Otherwise
running, the unit will beep 8 times and and the Full
the bucket will fall and cause the water to spill.
indicator light will flash, the digital display shows P2 .
Throw away the water and replace the bucket. The
Slowly pull out the bucket. Grip the left and right
bucket must be in place and securely seated for the
handles securely, and carefully pull out straight so
dehumidifier to operate.
water does not spill. Do not put the tank on the floor
The machine will re-start when the bucket is restored
because the bottom of the bucket is uneven. Otherwise
in its correct position.
the bucket will fall and cause the water to spill.
Throw away the water and replace the bucket. The
NOTES:
bucket must be in place and securely seated for the
When you remove the bucket, do not touch any parts
dehumidifier to operate.
inside of the unit. Doing so may damage the product.
The unit will re-start when the bucket is restored
The machine will re-start when the bucket is restored
Be sure to push the bucket gently all the way into the
in its correct position.
unit. Banging the bucket against anything or failing to
push it in securely may cause the unit not to operate.
NOTES:
When you remove the bucket, do not touch any parts
inside of the unit. Doing so may damage the product.
2. Continuous draining
Be sure to push the bucket gently all the way into the
Water can be automatically emptied into a floor
unit. Banging the bucket against anything or failing to
drain by attaching the unit with a water hose
push it in securely may cause the unit not to operate.
(O12mm) (not included).
Remove the water bucket from the front of the
2. Continuous draining
2. Continuous draining
unit, you will find a section of hose located
Water can be automatically emptied into a floor drain by
above the bucket.
Water can be automatically emptied into a floor
attaching a standard garden water hose (o 0.5 in./
Remove the rubber plug from the back of the
drain by attaching the unit with a water hose
o 12mm, not included).
unit and store it in a safe location (see Fig.8).
(O12mm) (not included).
• Remove the water bucket from the front of the
Insert the water hose through the hole in the
Remove the water bucket from the front of the
unit, you will find a section of hose located above
back of the unit and securely press it into the
unit, you will find a section of hose located
the bucket. Also, locate the fitting and (2) screws
connector on the front of the unit (Fig.9). Then
above the bucket.
included, either inside the bucket and/or within the
lead the water hose to the floor drain or a suitable
Remove the rubber plug from the back of the
drainage facility. Styrofoam base packing material.
unit and store it in a safe location (see Fig.8).
Replace the bucket in the unit. The bucket must
• Remove the rubber plug from the back of the unit
Insert the water hose through the hole in the
be in place and securely seated.
and store it in a safe location (see Fig. 8).
back of the unit and securely press it into the
• Insert the water hose through the hole in the back
connector on the front of the unit (Fig.9). Then
lead the water hose to the floor drain or a suitable of the unit and securely press it onto the connec-
NOTE: When the continuous drain feature is not being
drainage facility. tor on the front of the unit (Fig. 9). Next attach the
used, remove the drain hose from the connector and
Replace the bucket in the unit. The bucket must
opposite end of the hose to the fitting. Attach the
attach the back drain hole with the rubber plug shown
be in place and securely seated.
fitting with (2) screws provided to the back of the
in Fig.1.
unit. Then lead the water hose to the floor drain or a
suitable drainage location.
NOTE: When the continuous drain feature is not being
• Replace the bucket in the unit. The bucket must be
used, remove the drain hose from the connector and
in place and securely seated.
attach the back drain hole with the rubber plug shown
in Fig.1.
NOTE: When the continuous drain feature is not being used, remove the
drain hose from the connector as well as the fitting and screws. Then at-
tach the rubber plug back over the drain hole as shown in Fig. 8.
BHD-G Portable Dehumidifier
• Accessory drain hose, fitting and (2) screws are located inside bucket. On some models, the drain 1. Pull out the bucket a little.
1. Pull out the bucket a little.
2. Hold both sides of the bucket
2. Hold both sides of the bucket
2. Hold both sides of the bucket
securely and pull it out from
the unit.
Connector
Connector
8
8
8
Owner's Manual
Fig.5
with even strength, and pull it
out from the unit.
Fig.5
with even strength, and pull it
out from the unit.
Fig.6
3. Pour the water out.
Fig.6
Fig.7
3. Pour the water out.
Remove the
Fig.7
rubber plug
Push the hose
into the drain
Remove the
hole
rubber plug
Fig.8
Push the hose
Drain hose
into the drain
hole
Fig.8
Drain hose
Fig.9
Fig.9