Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Waring FP25
Summary of Contents for Waring FP25
- Page 1 FP25C Operation Manual for Waring FP25 and FP25C Food Processors...
-
Page 2: Important Safeguards
11. The use of attachments not recommended or sold by Waring may cause fire, electric shock or injury. NOTE: USER-INSTALLED CORDSET PLUGS ARE NOT PERMITTED IN EUROPE. 12. Do not use outdoors. -
Page 3: Table Of Contents
Assembly of Batch Bowl Parts (Cutter Bowl), FP25 & FP25C ....... -
Page 4: The Waring
FEED bled, the FP25 is only 19" high (48.9cm) and stores conveniently when not in use. For more compact stor- age, the cover can be stored upside down with the feed tube in the bowl. When stored this way, the unit is only 14 ⁄... - Page 5 (Batch Bowl Assembly continued) ASSEMBLY of BATCH BOWL PARTS FP25 & FP25C • Place the cover on the bowl, with the feed tube on the left, slightly toward the front. The locking tabs on the cover should be at the left of the locking tabs on the front rim of the work bowl.
-
Page 6: Assembly Of The Continuous Feed Chute Parts, Fp25C
DISASSEMBLY of BATCH BOWL PARTS ASSEMBLY of CONTINUOUS FEED CHUTE PARTS FP25 & FP25C FP25C • Clean and sanitize the motor base, and wash, rinse, and sanitize the continuous feed chute, cover, slinger ALWAYS UNPLUG THE CORD BEFORE DISASSEMBLING. disc, food pusher, food pusher insert and processing tools prior to initial use. -
Page 7: Operating The Controls
Two Pushers for Feed Tube OPERATING THE CONTROLS Pick up the large food pusher and the small food pusher. The large pusher is for processing larger vegeta- bles. The smaller pusher nests in the larger pusher and can be used for smaller vegetables, guiding long thin vegetables for more precise cuts and for jobs like slicing pepperoni. -
Page 8: Food Preparation
• Prepare all food items to be processed by washing and peeling as required. Remove pits, stones, and large seeds. FP25 & FP25C • Cut vegetables, meats, cheeses, etc. into sizes that will fit into your choice of small feed tube or large feed tube for processing with accessory discs, or into sizes as required by your processing task. -
Page 9: Use Instructions For Accessory Discs In The Continuous Feed Chute
• Always switch the food processor off by pressing and releasing the PULSE/OFF lever. This assures that the power is not supplied to the motor. FP25 & FP25C • Always switch the food processor off and wait until rotation stops before removing the cover. -
Page 10: Accessory Disc Selection And Use
Be sure the food will fit into the proper feed chute. Foods such as carrots, cucumbers, etc., should The FP25 and FP25C food processor disc accessories are made to perform a large variety of food process- be cut flat at both ends to provide a consistent slice throughout the whole product. With foods like cab- ing tasks: slicing, waved slicing, grating, shredding, French fry and julienne cuts. -
Page 11: Grating Operation
If unit does not operate after you have followed the above, and have tried the Safety Reset Switch • Check outlet to be sure there is current. FP25 and FP25C food processors come with a selection of six (6) different julienne plates with sizes up to ⁄ " x ⁄... -
Page 12: Safety Reset Switch
The SAFETY RESET SWITCH is provided for your convenience and to extend the life of your Waring food processor. It is located on the back of your machine, on the safety interlock tower, protected by a A stiff bristle brush will help to knock food particles out of the crevices of the discs and blades before round finger hole. -
Page 13: Processing Tools
2 mm x 2 mm ⁄ " x ⁄ " due to use or due to repairs or servicing by other than the Waring Service Center or a Factory Approved Waved Slicing Discs BFP26 2 mm x 4 mm ⁄... - Page 15 314 Ella T. Grasso Ave. IB-3672 www.waringproducts.com Torrington, CT 06790 Waring ® is a registered trademark of Waring Products Division of Conair Corporation. Any other trademark or service marks used herein are the trademarks or service marks of their respective owners.