1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Network Router
  5. TD-VG3631
  6. User giude

TP-Link TD-VG3631 User Giude

300mbps wireless n voip adsl2+ modem router
Hide thumbs
Table of Contents

Advertisement

Quick Links

TD-VG3631
300Mbps Wireless N VoIP ADSL2+ Modem Router
Rev: 1.0.1
1910010643

Advertisement

Table of Contents
loading

Related Manuals for TP-Link TD-VG3631

Summary of Contents for TP-Link TD-VG3631

  • Page 1 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router Rev: 1.0.1 1910010643...
  • Page 2 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3: Fcc Statement

    FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 4: National Restrictions

    National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Country Restriction Reason/remark General authorization required for outdoor use and Bulgaria None public service...

  • Page 5: Industry Canada Statement

    Industry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

  • Page 6: Declaration Of Conformity

    DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N VoIP ADSL2+ Modem Router Model No.: TD-VG3631 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...

  • Page 7: Table Of Contents

    CONTENTS Package Contents ....................1 Chapter 1. Product Overview...................2 1.1 Overview of the Modem Router ..................2 1.2 Main Features......................... 3 1.3 Panel Layout........................4 1.3.1 The Front Panel ........................4 1.3.2 The Back Panel........................6 Chapter 2. Connecting the Modem Router .............8 2.1 System Requirements ....................
  • Page 8 4.6 Wireless ........................43 4.6.1 Basic Settings ........................43 4.6.2 WPS Settings ........................45 4.6.3 Wireless Security ....................... 47 4.6.4 Wireless MAC Filtering ...................... 49 4.6.5 Wireless Advanced ......................51 4.6.6 Wireless Status ........................52 4.7 Voice..........................52 4.7.1 SIP Account ........................53 4.7.2 Dial Plan..........................
  • Page 9 4.12.3 WAN Host ......................... 86 4.12.4 Schedule........................... 88 4.13 Traffic Control ....................... 89 4.13.1 Control Settings ........................ 89 4.13.2 Rules List .......................... 89 4.14 IP&MAC Binding ......................90 4.14.1 Binding Settings........................ 91 4.14.2 ARP List..........................92 4.15 Dynamic DNS ....................... 92 4.16 Diagnostic ........................

  • Page 10: Package Contents

    Package Contents The following contents should be found in your package: One TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router One Power Adapter for TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Three RJ11 cables...

  • Page 11: Chapter 1. Product Overview

    300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router. 1.1 Overview of the Modem Router The TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.

  • Page 12: Main Features

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.2 Main Features Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), four RJ11 ports, two USB 2.0 ports Provides external splitter. Adopts Advanced DMT modulation and demodulation technology. Supports bridge mode and Router function.

  • Page 13: Panel Layout

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The Router’s LEDs are located on the front panel (View from left to right). They indicate the device’s working status. For details, please refer to LED Explanation.
  • Page 14 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide A valid PSTN connection. Incoming calls and outgoing calls are transmitted trough PSTN （Line） Flash line. PSTN connection fails. The phone is off hook. （Phone1-2） Flash The phone is ringing.

  • Page 15: The Back Panel

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 1.3.2 The Back Panel The Router's ports, where the cables are connected, and RESET button are located on the front. Figure 1-2 POWER: The Power plug is where you will connect the power adapter.
  • Page 16 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 1-3 WPS: The switch for the WPS function. For details, please refer to 4.6.2 WPS Settings. WiFi: The switch for the WiFi function. ON/OFF: The switch for the power.

  • Page 17: Chapter 2. Connecting The Modem Router

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 2. Connecting the Modem Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet). PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors. TCP/IP protocol on each PC.
  • Page 18 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 5: Power on the computers and LAN devices. Step 6: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to an electrical outlet or power extension. The electrical outlet shall be installed near the device and shall be easily accessible.

  • Page 19: Chapter 3. Quick Installation Guide

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configuring the PC After you directly connect your PC to the Modem Router or connect your adapter to a Hub/Switch which has connected to the Modem Router, you need to configure your PC’s IP address. Follow the steps below to configure it.
  • Page 20 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3...
  • Page 21 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically”...

  • Page 22: Quick Installation Guide

    192.168.1.2 ~ 192.168.1.254. 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
  • Page 23 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-8 Note: 1) Do not mix up the user name and password with your ADSL account user name and password which are needed for PPP connections. 2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
  • Page 24 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-9 Change the VPI or VCI values which are used to define a unique path for your connection. If you have been given specific settings for this to configuration, type in the correct...
  • Page 25 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-10 Here we select PPPoE WAN Link Type for example, enter the Username, Password and Confirm Password given by your ISP, and then click Next. Figure 3-11 On the Wireless screen, we use the default SSID, select Region and Mode. Set a Password or select Disable Security(Disable Security is not recommended.), and then click Next to...
  • Page 26 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Basic parameters of Voice can be set on the Voice screen. Please enter a profile name to identify this account and other parameters provided by your ISP. If you don’t want to configure VoIP function now, leave "Profile Name"...
  • Page 27 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 3-15...

  • Page 28: Chapter 4. Configuring The Modem Router

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration way. 4.1 Login After your successful login, you will see the fifteen main menus on the left of the Web-based utility.

  • Page 29: Quick Setup

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 4.4 Network Choose “Network”, there are many submenus under the main menu. Click any one of them, and...

  • Page 30: Wan Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.4.1 WAN Settings Choose “Network” “WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-2, which describes the WAN port settings and the relevant manipulation to each interface.
  • Page 31 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-3 4.4.1.1 Static IP Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below.
  • Page 32 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-4 ATM Configuration: VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP.
  • Page 33 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide DNS Server/ Secondary DNS Server: Here you can set DNS Server (at least one) manually. The Route will use this DNS Server for priority. Default Gateway: select a WAN Interface from the drop-down list as the IPv4 default gateway.
  • Page 34 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-5 Click Advanced, advanced selections for WAN Service Setup can be shown. MTU (bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.
  • Page 35 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Primary DNS Server/ Secondary DNS Server: Choose “Set DNS Server manually”, you can set DNS Server (at least one) manually here. The Route will use this DNS Server for priority.
  • Page 36 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Authentication Method: Select the Authentication Method from the drop-down list, the default method is AUTO_AUTH, and you can leave it as a default setting. Choose the right connection type according to your needs: For PPPoE connection, you can select Connect on demand or Connect automatically or Connect manually.
  • Page 37 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-7 4.4.1.5 IPoA If your ISP provides an IPoA connection, select IPoA option for the WAN service type on the screen.
  • Page 38 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-8 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you forget, you can ask your ISP. DNS Server/Secondary DNS Server: Type in your preferred DNS server.

  • Page 39: Ewan

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-9 Note: After you finish the Internet configuration, please click Save to make the settings take effect. 4.4.2 EWAN Choose “Network” “EWAN”, and you will see the Ethernet WAN Interface screen similar to Figure 4-10.
  • Page 40 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-10 4.4.2.1 Dynamic IP Select this option, the Modem Router will be able to obtain IP network information dynamically from a DHCP server provided by your ISP (as shown Figure 4-10). The next configuration is similar to Dynamic IP over ATM interface (see section 4.4.1.2 Dynamic...
  • Page 41 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-11 4.4.2.3 PPPoE If your ISP provides a PPPoE connection and you need to use an Ethernet Interface, select PPPoE option for the WAN service type on the screen. The following configuration is similar to PPPoE over ATM interface (see section 4.4.1.3...

  • Page 42: Interface Grouping

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-12 4.4.3 Interface Grouping Choose “Network” “Interface Grouping”, you can view all the current groups on this page (shown in Figure 4-13). Figure 4-13...

  • Page 43: Lan Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide VLAN: Enable or disable this function. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments.
  • Page 44 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-15 IP Address: You can configure the Modem Router’s IP Address and Subnet Mask for LAN Interface. • IP Address: Enter the Modem Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.

  • Page 45: Mac Clone

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide • Leased Time: The Leased Time is the amount of time in which a network user will be allowed connection to the Modem Router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased”...

  • Page 46: Dsl Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-17 Virtual Private Network (VPN) - VPN Passthrough must be enabled if you want to allow VPN tunnels using VPN protocols to pass through the Modem Router. PPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the •...

  • Page 47: Dhcp Server

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-18 DSL Modulation Type: Select the DSL operation Modulation Type which your DSL connection uses. Annex Type: Select the DSL operation Annex Type which your DSL connection uses. Click the Save button to save your settings.
  • Page 48 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-19 Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Modem Router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP Address must be 192.168.1.100 or greater, but...

  • Page 49: Clients List

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: To use the DHCP server function of the Modem Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect.

  • Page 50: Conditional Pool

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-21 MAC Address: The MAC address of the PC for which you want to reserve an IP address. IP Address: The IP address reserved for the PC by the Modem Router.
  • Page 51 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-23 To add a vendor class: Click the Add New button. Then Figure 4-24 will pop up. Enter parameters for the vendor class. Click the Save button. Figure 4-24 To modify or delete an existing entry: Click the Edit in the entry you want to modify.

  • Page 52: Wireless

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.6 Wireless Choose “Wireless”, there are six submenus to configure Wireless LAN settings. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.
  • Page 53 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 11bg mixed: Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802.11g mode is selected, only 802.11g wireless stations can be connected to the Modem Router.

  • Page 54: Wps Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide WEP Index: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the index of the WEP key. Auth Type: This option should be chosen if the key type is WEP(ASCII) or WEP(HEX). It indicates the authorization type of the Root AP.
  • Page 55 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-26, then Choose “Press the button of the new device in two minutes” and click Connect.

  • Page 56: Wireless Security

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button. Step 3: “Connect successfully” will appear on the screen of Figure 4-28, which means the client device has successfully connected to the Modem Router.
  • Page 57 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-29 Disable Wireless Security: If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security.

  • Page 58: Wireless Mac Filtering

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide • WEP Key - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network.
  • Page 59 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Description: A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New button. The following page will appear, shown in Figure 4-32:...

  • Page 60: Wireless Advanced

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Back button. The filtering rules that configured should be similar to the following list: 4.6.5 Wireless Advanced Choose menu “Wireless” ”Wireless Advanced”, you can configure the advanced settings of your wireless network.

  • Page 61: Wireless Status

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable Short GI: This function is recommended for it will increase the data capacity by...

  • Page 62: Sip Account

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.1 SIP Account Choose “Voice” “SIP Account”, you will see the screen similar to Figure 4-35. SIP accounts are necessary for making VoIP calls. This section introduces how to setup the SIP(Session Initiation Protocol) account for your Modem Router.
  • Page 63 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-36 SIP Account Basic Profile Name: Assign a name to identify the profile. Please note that special characters are not allowed. Phone Number: Enter the phone number of the account you applied.

  • Page 64: Dial Plan

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Preferred Receive Ptime: Ptime, short for packet time, refers to the time interval for a voice packet to be sent by the remote caller. The unit is ms (millisecond). Usually the default value 20ms is OK.
  • Page 65 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-37 Prefix: Displays the prefix of your plan. This prefix refers to the initial digit(s) of the numbers you dial. Op: Displays the operation of this plan. Destination: Displays the account or network used for this plan.
  • Page 66 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide If “TimeOut” is selected, the dialing will be sent out when timeout starts. The timeout activates when no more digits are dialed in a specific duration; If “#” is selected, the dialing will not be sent until “#” is dialed;...

  • Page 67: Phone Setup

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-40 Prefix: Set number(s) as the prefix. Up to 16 characters can be entered. Interface Barring: You can check any box to disable interface(s). Numbers matching prefix in Forbidden Call list are not allowed to be dialed out through the selected interface(s).
  • Page 68 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-42 Phone Enable: Check the box behind to enable the function. Dial Settings Dial Plan Priority: The parameters configured here determine which network or SIP account to use when making outgoing calls. In the 1 field, there are options of networks.
  • Page 69 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide • PSTN Preferred & Account X (a certain account) – The Router will select the network to make calls according to your dial plans set on Dial Plan page. If VoIP network is selected, the account used will be Account X.

  • Page 70: Advanced Setup

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide through selected account when "No answer" time is out. Please note that network or account available here varies with that in Dial Plan Priority field. Telephony Settings VAD Support: VAD(Voice Activation Detection) prevents transmitting the silence packets to consume the bandwidth.
  • Page 71 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide DSCP for SIP/RTP: DSCP(Differentiated Services Code Point) is the first 6 bits in the ToS byte. DSCP marking allows users to assign specific application traffic to be executed in priority by the next Router based on the DSCP value. Select DSCP for the SIP( Session Initiation Protocol ) and RTP(Real-time Transport Protocol) respectively.

  • Page 72: Speed Dial

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.7.5 Speed Dial Choose “Voice” “Speed Dial”, you will see the screen as shown in Figure 4-44. This section introduces how to configure Speed Dial for your account. Speed Dial function can help to store frequently used telephone numbers and make your dial more convenient.

  • Page 73: Call Firewall

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-47 Call Log: Check the Enable if you want to make this function take effect; otherwise check the Disable. Start: Beginning time of the call. Source: Caller ID, either phone number or IP address.
  • Page 74 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Call Firewall can be used to control incoming calls. This section introduces how to configure the Call Firewall. Choose “Voice” “Call Firewall“ “Mode Setting“, you will see the screen as shown in Figure 4-49.
  • Page 75 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-51 Enter a number with the length in the range of [3, 16]in the field of Black List Number and Click the Save button to make the configuration take effect, then you will go back to the previous page and see the following list as shown in Figure 4-50.

  • Page 76: Usb Voice Mail

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide in Black List and 2224 in White List, with Black List mode enabled, incoming call number 2224510 will be allowed. 4.7.8 USB Voice Mail Choose “Voice” “USB Voice Mail“, you will see the screen as shown in Figure 4-54. USB Voice mail is used to record voice messages when the call is not answered.
  • Page 77 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-55 Enable Local Play Operation Notify: Check this box so there will be sound indication for operation when you listen to the voice messages. This is enabled by default. If you are very familiar with the operations, you can disable it.

  • Page 78: Usb Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Input the PIN code according to the notification. You can listen to all the new messages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-54.

  • Page 79: User Accounts

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Capacity: The storage capacity of the USB driver. Status: Indicates the shared or non-shared status of the volume. Active means volume can be shared, while Inactive means volume can not be shared. If Deactivate in Action field is enabled, Inactive will be displayed in the Status field, which means volume can not be shared.

  • Page 80: Storage Sharing

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Re-enter the password in the Confirm Password field. Click the Set button, and then a new entry will be added in the table. Click the Apply button to apply your settings.

  • Page 81: Ftp Server

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-59 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings.
  • Page 82 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-60 Server Status: Indicates the FTP Server's current status. Internet Access: Enable or disable this function. Internet Address: If Internet Access is enabled, WAN IP will be displayed here.

  • Page 83: Media Server

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-61 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings.

  • Page 84: Print Server

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Server Enable: Select this box to enable this function. Server Name: The name of this Media Server. To add a new share folder for your media server, please follow the instructions below: Click Add New Folder button, and you will see the screen as shown in Figure 4-77.

  • Page 85: Route Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.9 Route Settings Choose “Route Settings”, it includes three menus: Default Gateway, Static Route and RIP Settings. The detailed descriptions are provided below. 4.9.1 Default Gateway Choose “Route Settings” “Default Gateway”, you can see the Default Gateway screen. You can select a WAN Interface from the drop-down list as the system default gateway.

  • Page 86: Rip Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-67 Enter the following data: Destination IP Address: The Destination IP Address is the address of the network or host that you want to assign to a static route.

  • Page 87: Forwarding

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Note: RIP cannot be configured on the WAN Interface which has NAT enabled (such as PPPoE). 4.10 Forwarding There are four submenus under the Forwarding menu: Virtual Servers, Port Triggering, DMZ and UPnP.

  • Page 88: Port Triggering

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select the service you want to use from the Common Service Port list. If the Common Service Port menu does not list the service that you want to use, enter the number of the service port or service port range in the Service Port field.
  • Page 89 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-71 To add a new rule, follow the steps below. Click the Add New button, the next screen will pop-up as shown in Figure 4-72. Select a common application from the Common Service Port drop-down list, then the Trigger Port field and the Open Ports field will be automatically filled.

  • Page 90: Dmz

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Open Protocol: The protocol used for Incoming Port, either TCP, UDP, or ALL (all protocols supported by the Modem Router). Status: The status of this entry, Enabled means the Port Triggering entry is enabled.

  • Page 91: Upnp

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-73 To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field.

  • Page 92: Parental Control

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Disable button to disable UPnP. Click the Refresh button to update the Current UPnP Settings List. 4.11 Parental Control Choose menu “Parental Control”, and you can configure the parental control in the screen as shown in Figure 4-75.

  • Page 93: Firewall

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide MAC Address of Current PC: This field displays the MAC address of the PC that is managing this Modem Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above.

  • Page 94: Lan Host

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Edit: Here you can edit or delete an existing rule. Add New: Click the Add New button to add a new rule entry. Enable Selected: Click the Enable Selected button to enable the selected rules in the list.

  • Page 95: Wan Host

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-78 Description: Here displays the description of the host and this description is unique. Address Info: Here displays the information about the host. It can be IP or MAC.
  • Page 96 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-80 In Description field, create a unique description for the host (e.g. Host_1). In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-81.

  • Page 97: Schedule

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.12.4 Schedule Choose menu “Firewall” → “Schedule”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-83. Figure 4-83 Description: Here displays the description of the schedule and this description is unique.

  • Page 98: Traffic Control

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click the Delete Selected button to delete the selected entries in the table. 4.13 Traffic Control There are two submenus under the Traffic Control menu: Control Settings and Rules List. Click any of them, and you will be able to configure the corresponding function.

  • Page 99: Ip&Mac Binding

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-86 Description: This is the information about the rules such as address range. Upstream Bandwidth: This field displays the max and mix upload bandwidth through the WAN port, the default is 0.

  • Page 100: Binding Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List. Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below.

  • Page 101: Arp List

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide To modify or delete an existing entry, follow the steps below. Find the desired entry in the table. Click Edit as desired on the Edit column. Click the Enable/ Disable Selected button to make selected entries enabled or disabled.

  • Page 102: Diagnostic

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-91 Service Provider: This field displays the service provider of DDNS. Domain Name: Enter the Domain name you received from dynamic DNS service provider. Username & Password: Type the “User Name” and “Password” for your DDNS account.

  • Page 103: System Tools

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 4.17 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics.

  • Page 104: Time Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-94 Save Locally: If Save Locally is selected, events will be recorded in the local memory. Minimum Level: Select the Minimum level in the drop-down list, for the Minimum Level, all logged events above or equal to the selected level will be displayed.

  • Page 105: Manage Control

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Enter the Time in Hour/Minute/Second format. Click Save. To set time automatically: Select your local time zone. Enter the address or domain of the NTP Server 1 or NTP Server 2.

  • Page 106: Snmp Settings

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-97 CWMP: Select enable the CWMP function. Inform: Enable or disable the function. If enabled, the information will be informed to ACS server periodically. Inform Interval: Enter the interval time here.

  • Page 107: Backup & Restore

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-98 An SNMP Agent is an application running on the Modem Router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs.

  • Page 108: Firmware Upgrade

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-100 Click the Restore button to reset all configuration settings to their default values. • The default User Name: admin • The default Password: admin • The default Subnet Mask: 255.255.255.0 Note: All changed settings will be lost when defaults are restored.

  • Page 109: Reboot

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use.
  • Page 110 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Figure 4-103 Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the Enable. If it is disabled, the function of DoS protection in Security settings will be disabled.

  • Page 111: Appendix A: Specifications

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix A: Specifications General ANSI T1.413.I2, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, IEEE802.1p, IEEE 802.11b,IEEE802.11e, IEEE 802.11g, IEEE Standards and Protocols 802.11n, IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT Safety &...

  • Page 112: Appendix B: Troubleshooting

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my Modem Router’s configuration to its factory default settings? With the Modem Router powered on, press and hold the RESET button on the front panel for 8 to 10 seconds before releasing it.
  • Page 113 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click Change adapter settings Right-click Local Area Connection Click Properties...
  • Page 114 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 115 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows Vista OS Go to Start > Settings >Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties...
  • Page 116 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 117 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide For Windows XP OS Go to Start > Control Panel, you will then see the following page. Click Network and Internet Connections Click Network Connections Right-click Local Area Connection Click Properties...
  • Page 118 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Double-click Internet Protocol (TCP/IP) Select Obtain an IP address automatically Select Obtain DNS server address automatically Click OK...
  • Page 119 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Click OK 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options...
  • Page 120 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Modem Router’s factory default settings and reconfigure your Modem Router following the instructions in Login.
  • Page 121 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 2) Insert the provided Resource CD into CD-ROM drive of your computer. 3) Please select your product model and click Start Setup. 4) Then the configuration wizard will pop up and show you how to connect your devices. After that,...
  • Page 122 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 5) When it comes to Configure USB Voice Mail page, check boxes before Configure USB Voice Mail and Send Files to USB Disk. Then click NEXT to continue. 6) Follow the step-by-step instructions until you comes to the finish screen. Click FINISH to close...
  • Page 123 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide 7) The configure files can be found in your USB device which means you have successfully configured the USB device for USB Voice Mail function.

  • Page 124: Appendix C: Telephony Features

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix C: Telephony Features This section introduces what the following features are used for. Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available.
  • Page 125 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Anonymous Call Blocking With this feature enabled, all anonymous calls will be blocked. Speed Dial This feature allows you to create short numbers for your frequently used telephone numbers to make your dialing more convenient.

  • Page 126: Appendix D: Telephone Operation

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix D: Telephone Operation The table below guides you to configure some frequently used call features using keypads on your telephone. For the features mentioned in this table, please refer to Telephony Features in Appendix C.
  • Page 127 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide effect. Pick up the phone to dial this code. After hearing the Enable Call Forwarding confirmation tone, hang up to make the configuration take on Busy. effect. Pick up the phone to dial this code. After hearing the...
  • Page 128 TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Disturb). confirmation tone, hang up to make the configuration take effect. Pick up the phone to dial this code. After hearing the Disable DND (Do Not confirmation tone, hang up to make the configuration take Disturb).

  • Page 129: Appendix E: Technical Support

    TD-VG3631 300Mbps Wireless N VoIP ADSL2+ Modem Router User Guide Appendix E: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details:...

Table of Contents