Download
Share
Print this page
Bunn FMD-4 Installation & Operating Manual
  1. Manuals
  2. Brands
  3. Bunn Manuals
  4. Beverage Dispenser
  5. FMD-4
  6. Installation & operating manual
Bunn FMD-4 Installation & Operating Manual

Bunn FMD-4 Installation & Operating Manual

Dispenses hot beverages or soups on demand from powdered product
Hide thumbs Also See for FMD-4:
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual See also: Service & Repair Manual, Operation & Service Manual
FMD-4
FMD-5
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601
FAX: (217) 529-6644
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
35135.0000F 01/10 ©2003 Bunn-O-Matic Corporation

Advertisement

loading
Need help?

Need help?

Do you have a question about the FMD-4 and is the answer not in the manual?

Questions and answers

Related Manuals for Bunn FMD-4

Summary of Contents for Bunn FMD-4

  • Page 1 To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
  • Page 2 SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.
  • Page 3 THIS APPLIANCE IS HEATED WHENEVER CONNECTED TO A POWER SOURCE 00831.0000F 3/98 ©1998 BUNN-O-MATIC CORPORATION 00831.0000 200 F 190 F 180 F APPROXIMATE THERMOSTAT TEMPERATURE SETTINGS 28368.0004A 08/08 © 2008 BUNN-O-MATIC CORPORATION 28368.0004 37881.0000 FMD-4 28964.0004 FMD-5 28964.0003 FMD-4 28328.0008 FMD-5 28328.0009 35135 051909...

  • Page 4: Electrical Requirements

    90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water inlet fitting is .75- 11.5 NH (HOSE THREAD). For convenience an elbow adaptor is provided to convert to a 1/4˝ flare fitting. Bunn-O-Matic does not recommend the use of a reverse-osmosis or deionized water supply to this equipment.
  • Page 5 INITIAL FILL & HEAT CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Turn-on the water supply and connect the dispenser to the power source. 2. Water will automatically flow into the tank to the proper level and then shut-off. This will take less than five minutes.

  • Page 6: Preventive Maintenance

    PREVENTIVE MAINTENANCE Bunn-O-Matic Corporation recommends that preventive maintenance be performed at regular intervals. Maintenance ® should be performed by a qualified service technician. For Technical Service, contact Bunn-O-Matic Corporation at ® 1-800-286-6070. NOTE: Replacement parts or service caused by failure to perform required maintenance is not covered by warranty.
  • Page 7 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur- faces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. 1 x 24h 1. Rinse out Whipper Chambers by placing RINSE/RUN 1.

This manual is also suitable for:

Fmd-5