Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HP 24wd
Summary of Contents for HP 24wd
- Page 1 HP 24wd LED Backlit Monitor User Guide...
- Page 2 Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Chapter I. Introduction
Chapter I. Introduction 1.1 Features Multilingual OSD adjustment Compatible with IBM VGA, extended VGA, VESA VGA, SVGA, XGA, and SXGA modes Wide range of applicable voltages (AC 100-240V 50/60Hz ) enables direct use without any setting. Plug-and-play VESA DDC1/ 2B Standard. Compatible with Windows 9x / 2000 / XP / 7 / Vista operation systems 1.2 Check list Please make sure the following items are included with your LCD monitor;... -
Page 4: Install The Pedestal
Chapter II. Installation 2.1 Install the pedestal Please follow the steps illustrated below to install the pedestal. -
Page 5: Connect Your Monitor To Your Computer
2.2 Connect your monitor to your computer Power off and unplug your computer. Connect the 15-Pin ends of the signal cable to the VGA port of your monitor and the VGA OUT jack on the back of your computer. Secure the screws on both ends of the signal cable. Connect the round end of power adapter to the monitor, then connect one end of the power cords to the power adapter and the other end to the nearest electrical outlet. - Page 6 2.3 Disconnect the pedestal for shipping Press the clip button on the pedestal and remove the pedestal from the stand.
-
Page 7: Chapter Iii. Monitor Overview
Chapter III. Monitor overview Overview of front panel controls... -
Page 8: Operational Instruction
Chapter IV. Operational Instruction 4.1 Power ON/OFF Switch Press this button to power on/off your monitor. Note: The ON/OFF switch does not disconnect your monitor from the main voltage. To completely disconnect the main voltage, please remove the power plug from the socket. 4.2 Power indicator The power LED is blue when the monitor operates normally. - Page 9 4.4 OSD operational instructions Main menu Icon Submenu option Note option To adjust the brightness level of the Brightness screen. The factory default range is To adjust the contrast level of the Contrast screen.The factory default range is Selects the screen color.The Color factory is 6500K or Custom color,depending on the mode.
- Page 10 characters (only applicable to VGA input) To adjust the horizontal position of Horizontal position an image (only applicable to VGA input). To adjust the vertical position of an Vertical position image (only applicable to VGA input). Selects the method on how displayed information on the monitor will be formatted.Select Fill to Screen –...
- Page 11 “30 seconds”. To select the function of power Management management for your monitor. To enable the energy-saving function, Select Power Saver The factory default setting is On. Restores power to the monitor following an unexpected removal of power. Select: Power-On Recall The factory default is On.
- Page 12 Set current time – to set the current time in hours and minutes. Set sleep time – to set the desired time when your monitor works under the sleeping mode. Set On time – to set the desired time when your monitor is awakened from the sleeping mode.
-
Page 13: Chapter V. Technical Information
Chapter V. Technical Information 5.1 Factory preset display mode Criteria Resolution Horizontal frequency Vertical frequency 640X480 @60 Hz 31.469 59.94 720X400 @70 Hz 31.469 70.087 800X600 @60 Hz 37.879 60.317 1024X768 @60 Hz 48.363 60.004 1280X720 @60 Hz 45.00 60.00 1280X1024 @ 60 Hz 63.981 60.02... -
Page 14: Product Specifications
5.2 Product specifications Size 23.6" wide screen Max. resolution 1920 x 1080 @ 60 Hz Recommended resolution 1920 x 1080 @ 60 Hz Horizontal frequency 24-94 kHz Vertical frequency 50-76 Hz Viewable size 521.28x 293.22 mm Viewable angle 170 (H) 160 (V) Pitching angle -5º... - Page 15 5.3 Signal cable connector Signal Red Signal Green Signal Blue Signal Ground Cable testing Red Signal Ground Green Signal Ground Blue Signal Ground 5 VDC Null Ground SDA (for DDC) Horizontal synchronization Vertical synchronization SCL (for DDC) VGA Interface...
-
Page 16: Panel Testing
SIGNAL TMDS Data 2 - TMDS Data 2 + TMDS Data 2 / 4 Shield TMDS Data 4 - TMDS Data 4 + DDC Clock DDC Data No Connect TMDS Data 1 - TMDS Data 1 + TMDS Data 1 / 3 Shield TMDS Data 3 - TMDS Data 3 + +3.3/+5V Power (from PC) -
Page 17: A Safety And Maintenance Guidelines
Use a power strip whose manufacturer offers a Damage Replacement Policy so you can replace the equipment, if surge protection fails. Use the appropriate and correctly sized furniture designed to properly support your HP LCD monitor. WARNING! LCD monitors that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, or carts may fall over and cause personal injury. - Page 18 Safety Precautions Use only a power source and connection compatible with this monitor, as indicated on the label/ back plate of the monitor. Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of the products connected to the power cord does not exceed the rating of the power cord.
-
Page 19: Maintenance Guidelines
● Do not open your monitor cabinet or attempt to service this product yourself. Adjust only those controls that are covered in the operating instructions. If your monitor is not operating properly or has been dropped or damaged, contact your HP authorized dealer, reseller, or service provider. -
Page 20: B Agency Regulatory Notices
(1.8 m) and 12 feet (3.6 m).If you have questions about the type of power cord to use, contact an authorized HP service provider. A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. - Page 21 ENERGY STAR Qualification ○ ○ HP Displays marked with the ENERGY STAR certification mark meet the requirements of the ○ U.S. Environmental Protection Agency (EPA) ENERGY STAR program. The EPA ENERGY STAR ○ certification mark does not imply endorsement by the EPA. As an ENERGY STAR ○...
- Page 22 Chemical Substances HP is committed to providing our customers with information about the chemical substances in our products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the European Parliament and Council). A chemical information report for this product can be found at http://www.hp.com/go/reach.
- Page 23 Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling or waste electrical and electronic equipment.
-
Page 24: C Troubleshooting
Restart your computer to activate the new setting. Adjust the contrast and brightness controls. Blurred and ghost Make sure no extension cord or switch box is used. HP suggests you to image. connect your monitor to the graphic card output port on the back of your computer. -
Page 25: Contacting Support
The LED will light or fade out. Contacting Support You may contact the customer service department by visiting HP technical support website at: www.hp.com/support Select the country / territory where you are. Follow the link to visit pages applicable to your monitor.