Table of Contents
Advertisement
* Mark: Applicable input signal for Component (Y, P
525 (480) / 60i
525 (480) /60p
750 (720) /60p
1,125 (1,080) /60i
1,125 (1,080)/60p
1,125 (1,080)/60p
1,125(1,080)/24p
1,125(1,080)/24p
640 × 400 @70
640 × 480 @60
Macintosh13" (640 × 480)
640 × 480 @75
852 × 480 @60
800 × 600 @60
800 × 600 @75
800 × 600 @85
Macintosh16" (832 × 624)
1,024 × 768 @60
1,024 × 768 @70
1,024 × 768 @75
1,024 × 768 @85
Macintosh 21" (1,152 × 870)
1,280 × 768 @60
1,280 × 1,024 @60
1,366 × 768 @60
Note
Signals other than above may not be displayed properly.
The above signals are reformatted for optimal viewing on your display.
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
Some PC models cannot be connected to the set.
There is no need to use an adapter for computers with IBM PC/AT compatible D-sub 15P terminal.
The maximum resolution: 1,280 × 1,024
If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.
Signal Names for D-sub 15P Connector
5
4
3
2
1
10
9
8
7
6
15 14 13 12 11
Pin Layout for PC Input Terminal
HDMI connections to some Panasonic equipment allows you to interface automatically. (p. 23)
This function may not work normally depending on the equipment condition.
The equipment can be operated by other remote controls with this function on even if TV is in Standby mode.
Image or sound may not be available for the first few seconds when the playback starts.
Image or sound may not be available for the first few seconds when Input mode is switched.
Volume function will be displayed when adjusting the volume of the equipment.
If you connect equipment that has "HDAVI Control 2 or later" function to the TV with HDMI cable, the sound from DIGITAL
AUDIO OUT terminal can be output as multi channel surround.
"HDAVI Control 5" is the newest standard (current as of December, 2011) for the HDAVI Control compatible equipment.
This standard is compatible with the conventional HDAVI equipment.
Input signal that can be displayed
, P
B
R
horizontal frequency (kHz)
15.73
31.47
45.00
33.75
67.43
67.50
26.97
27.00
31.47
31.47
35.00
37.50
31.44
37.88
46.88
53.67
49.73
48.36
56.48
60.02
68.68
68.68
47.78
63.98
48.39
PC Input Terminals Connection
Pin No.
Signal Name
R
G
B
NC (not connected)
GND (Ground)
VIERA Link
TM
), HDMI and PC
vertical frequency (Hz)
59.94
59.94
59.94
59.94
59.94
60.00
23.98
24.00
70.08
59.94
66.67
75.00
59.89
60.32
75.00
85.08
74.55
60.00
70.07
75.03
85.00
75.06
59.87
60.02
60.04
Pin No.
Signal Name
GND (Ground)
GND (Ground)
GND (Ground)
NC (not connected)
GND (Ground)
"HDAVI Control
TM
"
COMPONENT
HDMI
*
*
*
*
*
*
*
*
*
*
*
*
Pin No.
Signal Name
NC (not connected)
NC
HD/SYNC
VD
NC
PC
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
37
Advertisement
Table of Contents
