Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grundig WT2
Summary of Contents for Grundig WT2
- Page 1 WIRELESS TRANSMITTER DEUTSCH ENGLISH FRANÇAIS ITALIANO PORTUGUÊS...
-
Page 2: Package Contents
Since the audio signals are not transmitted on an exclusive range, we cannot guarantee that this will not cause interference. To avoid such interference, 16 different channel combinations are provided on the WT2 channel selec- tion switch. -
Page 3: Operating Modes
You can operate one or up to four active loudspeakers with the WT2. When using 4 LSP2/LSP3 or RS Set 2 active loudspeakers, each active loudspea- ker can be defined for the WT2 – depending on the location of the tele- vision – as left/right and front/rear speaker. - Page 4 OPERATING MODES ___________________________ System configuration in Surround mode Television Seating position LSP2 LSP2 LSP3 LSP3 RS Set 2 RS Set 2 System configuration in Stereo mode LSP2 LSP2 Television LSP3 LSP3 Seating position Dolby Pro Logic or Dolby Digital mode LSP2 Television LSP2...
-
Page 5: Set-Up And Safety
The assembly of the WT2 and the installation of the active loudspeakers are to be performed by the dealer. WT2 is designed for the sending of audio signals as well as the sending and receiving of data signals. Any other use is expressly prohibited. - Page 6 Antenna jack for supplied antenna cable (with FineArts Planavision, the antenna cable is already built-in). Jack for I C bus cable for data exchange with a Grundig television with I C connec- tion (e.g. Lenaro). SPEAKER INSTALL I 2 C...
-
Page 7: Connecting Active Loudspeakers
WT2 transmitter. The same applies to using the LSP2/LSP3 or RS Set 2 active loudspeakers as stereo rear loudspeakers or as mono rear loudspeakers. - Page 8 Connecting the WT2 to FineArts Vision With the WT2, you may operate up to 4 wireless active loudspeakers with your television. To do this, the following table shows how to connect WT2 to the television using the supplied cinch cables.
-
Page 9: Displaying The Software Version
If you want front loudspeaker operation (Stereo and Dolby Pro Logic), the LF DPL component must be changed from .03 to .13 (see the WT2 assembly instructions with information on converting from .03 to .13). »F F Press «... - Page 10 PREPARATION (FAV/FAP) _____________________________ In the »LS CONFIGURATION-SELECTION« menu, press H I F I LS CONFIGURATION - SELECTION STEREO »P+« or »P-« to select the »SSubwoofer internal« item and press » « or » « to select »no«. Left/right speaker internal external Note: Center speaker...
- Page 11 PREPARATION (FAV/FAP) _____________________________ Note: H I F I LS CONFIGURATION - SELECTION STEREO If stereo front loudspeakers are already installed, on televisions with 29798-102.07 software the »Left/right Left/right speaker Active box speaker Active box« item appears in the »LS CONFI- Center speaker GURATION-SELECTION«...
- Page 12 (Euro and right angle connectors). Initial installation of a pair of loudspeakers If the WT2 is in its original state, the transmitter starts automatically in instal- lation mode after connection to the mains (initial installation). The WT2 is factory adjusted for two loudspeakers (»SPEAKER INSTALL CH-SEL-...
- Page 13 _____________________________ Initial installation of two pairs of loudspeakers If the WT2 is in its original state, the transmitter starts automatically in instal- lation mode after connection to the mains (initial installation). In the following example, you will therefore first install two pairs of loudspeakers (stereo front left/right and mono rear left/right).
- Page 14 Replace the rear cover of the television only after the transmission quality has been tested with WT2. Note: WT2 may only be operated with the supplied mains cable (Euro and right angle connectors). Adjusting the Dolby volume In the menu »INSTALLATION« use »P+« or »P-« to sel- ect the line »Dolby level adjustment«...
-
Page 15: Installation
... for Grundig televisions with I C connection (e.g. Lenaro) Note: Installation and connection of the WT2 may only be performed by an aut- horised Grundig dealer. For televisions with I C connection, the installation of the wireless trans- mission is carried out through menus on the television screen. If the appro- priate software is not integrated in the television, the dealer must install an update. - Page 16 Registering WT2 with the HiFi system FineArts Audion When you simultaneously operate WT2 with the HiFi system FineArts Audion, you must register the wireless module with the HiFi system. This pro- cedure is described in the installation instructions from FineArts Audion.
- Page 17 INSTALLATION (I _____________________________________ System configuration, e.g. for Lenaro The system configuration, which is automatically set up during installation, can be checked in the following ways: Call up the television menu »EASY DIALOG« with » «. Select the menu »Installation« with »P+« or »P-« and activate with »OK«.
- Page 18 SETTINGS (I _____________________________________ Adjusting the Dolby volume For Dolby Digital mode, all loudspeakers must be set with equal volumes in relation to each other. The Dolby level must be set only once after installation and is retained for further operation thereafter. Call up the menu »EASY DIALOG«...
- Page 19 »0...9« and confirm with »OK«. Quit the setting with » «. Notes: This completes the installation and WT2/TV configuration. The loudspeakers automatically switch to stand-by when the television is switched to stand-by or is switched off using the power switch.
-
Page 20: Operation
OPERATION __________________________________________ Switching the installed system on again When switching on an installed system whose individual components have been switched off at the power switch, proceed as follows: Turn on the active loudspeakers with the mains switch. – The indicators on the active loudspeakers light up orange (stand-by). Switch on the television. -
Page 21: System Upgrade
... for the Grundig televisions FineArts Vision (FAV) and Planavision (FAP) If you operate two stereo front loudspeakers over the WT2 for example, and wish to then add two mono rear loudspeakers, a reinstallation must be per- formed. Please note the necessary pre-settings for the stereo front and mono rear loudspeakers (pages 35 and 36), and the installation sequence. - Page 22 SYSTEM UPGRADE _____________________________ ... for Grundig televisions with I C connection (e.g. Lenaro) For televisions with I C connection, the reinstallation of loudspeakers is car- ried out through the menus on the television screen. Installation data, if pre- sent, need not be deleted.
- Page 23 Set the Dolby level and Dolby processing times as described on pages 44 to 45. Resetting the WT2 to its original state Note for dealers: With this function you can delete all existing installation data and reset the WT2 to its original state.
-
Page 24: Rectifying Minor Problems
This can lead to noise or a temporary loss of sound. When such a problem occurs, it usually suffices to reposition the loudspeaker or select a different channel combination on the WT2. If the remedies below are not successful, please consult an authorised Grundig dealer. - Page 25 Disconnect the power cord installed. from the WT2 and plug it in again after a short time. Switch on the loudspeak- ers. I C only: using the power switch, switch off the television and switch it on again shortly afterwards.
-
Page 26: Additional Information For Units Sold In The Uk
“E”, earth symbol “ ”, coloured green, or green & yel- low. Replacement mains lead sets can be obtained from your local dealer, or by contacting Grundig Consumer Relations (01788 570088) Moulded 3-pin lead set, suitable for UK use: Ref: Leadset UK 8290-991-224... -
Page 27: Technical Data
INFORMATION ___________________________________________ The wireless WT2 is noise-suppressed according to the applicable EU direc- tives. These products fulfil the European directives 89/336/EEC, 73/23/EEC and 93/68/EEC. This device conforms to the safety regulation DIN EN 60065 (VDE 0860) and therefore the international safety regulation IEC 60065. - Page 28 Grundig AG Beuthener Str. 41 • D-90471 Nürnberg • http://www.grundig.com 28017 942 2000 •...
Need help?
Do you have a question about the WT2 and is the answer not in the manual?
Questions and answers