System Menu - American DJ Accu Spot 250 II User Instructions

Accu Spot 250 II™
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
American DJ - www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 13
®
Some manufactures use 5-pin DMX-
5-Pin XLR Male (In)
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Set Up Accu Spot 250 II™
0 ADDR
1 TEST
2 PLA Y
3 LAMP
4 RESE
5 TIME
6 RPAN
7 RTL T
8 MIC
9 DISP
10 SPEC
11 EDIT
American DJ
®
AXXX A001
T-01~T-XX
RUN MSTR/ALON
AUDI MSTR/ALON
AUT O OFF / RUN /AUDI
ON/OFF
ALL
SCAN
COLR
GOBO
SHTR
LIFE 0000~9999
LAMP 0000~9999
CLMP
ON/OFF
ON/OFF
M-XX
VALU D–XX D-00 (DXXX)
D ON ON/OFF
FLIP ON/OFF
LAAU ON/OFF
RDMX ON/OFF
MODE 8 CH/9 CH
DLOF ON/OFF
DLA Y D–XX D-05
SPOT ON/OFF
DFSE ON/OFF
FEED ON/OFF
VER V1.0~V9.9
CODE CXXX
ADJU
CH01~CH30 XXXX(-128~127)
STEP S–01 ~S–48
0 1 XX(00~FFH)
C–01~C–30
3 0 XX(00~FFH)
SCXX
TIME T XXX(001~999)
CEDT ON/OFF
REC. RE.XX
RUN ON/OFF
- www.americandj.com - Accu Spot 250 II™ Instruction Manual Page 14

System Menu

Indicate the staring DMX address
A001 also is the settingfor slave
Automatically test the function
Runs xture as "master" or "alone" for auto
Runs xture as "master" or "alone" for audio
Runs xture for no DMX
Manually switches lamp "on" and "off"
Reset all motorsand returns xture to home
Reset only motorsfor pan/tilt
Reset only motorsfor colors
Reset only motorsfor goboand rotation
Reset only motorsfor shutterand/ordimmer
Displays the total xture runningtime
Displays a lamps runningtime
Clear lamp runningtime
Reverses the pan movements
Reverses the tilt movements
Mic sensitivity
Display the DMX512 value of each channel
Display turn off after 2mins
This function will reverse the display 180
Automatic lamp start with power
Change DMX addressvia external controller
Channel modeselect
Switch lamp via DMX
Lamp on delay time
Lamp optimization
Resets all the xture functions to default
Pan/tilt feedback (error correction) on/of f
Software version
Fixture code *code is "C050"
Motor Calibration
Set the amountof your program
Edit the channelsof each scene
Time for each scene
Edit programvia controller
Auto Save
Program test