Denon DBP-2010 Owner's Manual page 39

Function Setup
To make the most of its feature, set up your speakers appropriately by referring to the table below.
Speaker setting options are available at the following locations;
<Speaker setting for the audio signal output from the HDMI OUT jack >
(Available when you have HDMI cable connected to the HDMI OUT jack)
SETUP A Quick A HDMI Audio Out A HDMI Multi(LPCM)
SETUP A Custom A Audio A HDMI Audio Out A HDMI Multi(LPCM)
<Speaker setting for the audio signal output from the 7.1ch AUDIO OUT jacks >
SETUP A Quick A 7.1ch Audio Out A Multi Channel
SETUP A Custom A Audio A 7.1ch Audio Out A Multi Channel
How to navigate through the "HDMI Multi(LPCM)" and "Multi Channel" setting
1) Use [ / ] to select the menu item.
2) Use [ / ] to select setting items.
• Use [RETURN] to go back to the previous screen.
3) Use [ / ] to select desired options. (Except for "Test Tone" and "Default".)
For "Test Tone":
Use [ / ] to select "Manual" or "Auto", then press [ENTER].
• The test tone will be output. If you select "Manual", use [
[ / ] to adjust the volume. If you select "Auto", use [
that output the test tone.
• If you want to stop the test tone, press [RETURN].
For "Default":
Press [ENTER] to reset the "Speaker Configuration", "Channel Level" or "Delay Time"
setting to the default.
4) Press [SETUP] to exit.
Menu Setting items
Speaker Configuration Front*
Select the desired
speaker to set. Then
Center
change the setting
appropriately by
referring to the
Subwoofer
descriptions.
Surround
Surround Back
Default
: Displaying the menu
Remote control operation
buttons
Cancel the menu
/ ] to select desired speaker, then use
/ ] to adjust the volume of the speaker
Options Descriptions
Large* Large:
For the large speakers
Small
with strong low frequency
Large*
reproduction capabilities.
Small:
Small/None
For the small speakers
On*
which do not provide
None
strong bass sound.
None:
Large*
No speakers.
Small/None
For "Subwoofer" there is
Large*
only "On" or "None".
Small/None
Select "Default", then
press [ENTER] to reset the
"Speaker Configuration"
setting to the default.
: Move the cursor
(Up/Down/Left/Right)
ENGLISH
• For "Speaker Configuration" setting, the settings of each speaker size may be adjusted
automatically corresponding to each setting. (e.g. If "Front" is set to "Small", you cannot set
"Center", "Surround" and "Surround Back" to "Large".)
• If you connect to 5.1-channel surround system, set "Surround Back" in "Speaker Configuration" to
"None".
• "None" for "Center", "Subwoofer", "Surround" and "Surround Back" is not available for the speaker
setting for the audio signal output from the HDMI OUT jack .
Menu Setting items
Channel Level Test Tone*:
Tests or sets the "Test Tone" is the test
volume for each tone which can be
speaker. output from the
speakers so that you
can adjust the volume
for each speaker.
Front Lch
Center
Front Rch
Surround Rch
Surround Back Rch
Surround Back Lch
Surround Lch
Subwoofer
Default
: Confirm the setting
34
ENGLISH
Function Setup
Options Descriptions
Off* Select "Off" to deactivate
the "Test Tone" feature.
Select "Manual", then
press [ENTER] to manually
Manual
set the volume for the
desired speaker.
Select "Auto",then press
Auto
[ENTER] to automatically
output the test tone from
each speaker.
0 dB to -12 dB If you have selected
(0 dB*) "Manual" in "Test Tone",
select the desired speaker
0 dB to -12 dB
to set and adjust the
(0 dB*)
volume for the selected
0 dB to -12 dB
speaker.
(0 dB*)
If you have selected
0 dB to -12 dB
"Auto" in "Test Tone", test
(0 dB*)
tone will be output
automatically in order.
0 dB to -12 dB
Adjust the volume of the
(0 dB*)
speaker that output the
0 dB to -12 dB
test tone.
(0 dB*)
0 dB to -12 dB
(0 dB*)
0 dB to -12 dB
(0 dB*)
Select "Default", then
press [ENTER] to reset the
"Channel Level" setting to
the default.
: Return to previous menu