L or coloured RED. When replacing the fuse only a correctly rated approved type should be used and be sure to re-fit the fuse cover. IF IN DOUBT — CONSULT A COMPETENT ELECTRICIAN. – TASCAM IF-TAD...
Page 3
CAUTION Changes or modifications to this equipment not expressly approved by TEAC CORPORATION for compliance could void the user’s authority to operate this equipment. TASCAM IF-TAD –...
Page 4
Für Kunden in Europa Warnung Dies is eine Einrichtung, welche die Funk-Entstörung nach Klasse A besitzt. Diese Einrichtung kann im Wohnbereich Funkstörungen versursachen ; in diesem Fall kann vom Betrieber verlang werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen. – TASCAM IF-TAD...
9) A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. TASCAM IF-TAD –...
Page 7
18) Object and Liquid Entry — Never push objects of any kind into this product through openings as they may touch dangerous volt- TASCAM IF-TAD –...
Page 8
23) Wall or Ceiling Mounting — The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 24) Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. – TASCAM IF-TAD...
Page 9
The IF-TAD supports the standard sampling frequencies of 44.1 kHz and 48 kHz. The IF-TAD supports a variety of word lengths, up to 24 bits. When 20-bit or 24-bit data is transmitted to 16-bit units, rounding or truncation is performed by the receiving device.
WARNING Always use only the PS-P414 power supply designed for use with the IF-TAD. Do not use any other power adapter, or damage may occur to the IF-TAD. WORD SYNC OUT This BNC connector provides a standard word clock output, based on the word clock derived from the unit to the connected adat device.
Page 11
IN and OUT connectors Use these connectors to make the appropriate connections (IF-TAD IN to the adat device’s optical OUT and the IF-TAD OUT to the adat device’s optical IN). Use only optical audio cables as recommended by the manufacturer of the adat device.
Page 12
flashing, this probably means that both the TDIF-1 device and the adat device have been selected as clock sources. Rectify this situation by selecting one device as a clock master and the other as a clock slave. – TASCAM IF-TAD...
Word clock selection As mentioned earlier, one, and only one, of the devices connected to the IF-TAD must be acting as a word clock master. If both devices are selected as a word clock master device, the indicators 4 and 6will flash, and the IF-TAD will not function.
Page 14
IF-TAD Interface • On the TASCAM DA-98 and DA-88 DTRS recorders, the CLOCK key is used to select between the different clock sources available. If this is set to INT, the word clock is be internally derived, or if a word clock is available at the BNC WORD IN connector, the word clock is taken from there.
Page 15
Some models of ADAT recorder record and play back digital data at 20-bit resolution. • On the TASCAM DA-38 and DA-98 recorders, if a 16-bit input word length is selected, 20-bit data will be truncated to the 16 bits recorded on the DTRS recorder. If 20-bit or 24-bit...
Page 16
ADAT Word clock Note that here the ADAT recorder acts as the word clock master, and the DTRS recorder takes its clock reference from the IF-TAD through the IF-TAD’s WORD SYNC OUT connector. TASCAM digital mixer and ADAT LX20 recorder...
Page 17
first with the word clock synchronization, but using the PITCH UP and PITCH DOWN keys to change the pitch away from standard, and then re-set to standard pitch will usually re-lock the word synchronization (as described in 2.2, "Problems which may occur"). TASCAM IF-TAD –...
Power input and indicator For use with PS-P414 only Dimensions (w x h x d) 191 x 38 x 116 (mm), 7.5 x 1.5 x 4.6 (in) Weight (IF-TAD only) 750 g (1.65 lbs) Power requirements USA/Canada 120 VAC, 60 Hz (PS-P414)
Need help?
Do you have a question about the IF-TAD and is the answer not in the manual?
Questions and answers