Advertisement

������ �� �������� �����
Manual
doro 312C

Advertisement

Table of Contents
loading

Summary of Contents for Doro 312C

  • Page 1 ������ �� �������� ����� Manual doro 312C...
  • Page 2 12 One-touch memory buttons M1/ 4 Select Caller ID mode 13 Scrolling Buttons 5 Handset Volume Control 14 New CID message and Visual 6 Store Button Ring Indicator 7 Memory button 15 Select Phone Book mode 8 Recall button 9 Redial button www.doro.com...
  • Page 3: Installation

    1. Disconnect the telephone line cord. 2. On the underside of the telephone carefully remove the battery cover. 3. Insert the backup batteries ensuring correct battery polarity is observed. 4. Replace the battery cover. 5. Reconnect the telephone line cord. www.doro.com...
  • Page 4: Wall Mounting

    Caller ID memory will be shown in the display. The display will illuminate during ringing, when accessing memory functions and dialling out. Ringer signal The ringer can be adjusted using the switches located on the side of the telephone: Ringer volume Ringer melody www.doro.com...
  • Page 5: Operation

    If the number dialled is engaged or you wish to redial the last number called simply lift the handset (or press ) and press Volume control The handset earpiece volume may be adjusted during a call using To adjust the speaker volume (hands free), use located on the side of the telephone. www.doro.com...
  • Page 6: Hands Free Function

    The switch over between speaker and microphone is automatic and dependent on the sound level of the incoming call and the microphone respectively. It is therefore essential that there are no loud noises, e.g. music, in the immediate vicinity of the telephone, as this will disrupt the speaker function. www.doro.com...
  • Page 7 (see the table above). 6. Press Press if you need to insert a pause in the telephone number. If you wish to change a number, store the new number in the same location as the old one. www.doro.com...
  • Page 8 Deleting all entries in the Phone Book 1. Press 2. Scroll to the required memory location using 3. Press and hold until the display shows DELETE ALL? 4. Press and hold until the displayed telephone number disappears. www.doro.com...
  • Page 9 3. Select a memory location by pressing the relevant keypad digit Press if you need to insert a pause in the telephone number. If you wish to change a stored telephone number, store the new number in the same location as the old one. www.doro.com...
  • Page 10: Caller Identification

    It is an International call or a call from a PBX (no OUT OF AREA information received). Information on the number is blocked. The call could PRIVATE also be from a PBX. New number not previously recorded or logged. Several calls have been received from the same caller. www.doro.com...
  • Page 11 The unit is now set up to insert 0/00 when using the dial back feature from the CID log in accordance with Telecom NZ requirements. If a charge for local calls is unacceptable the dial back feature should not be used, refer to page 15. www.doro.com...
  • Page 12: Troubleshooting

    It may not be possible to receive Caller ID information if the phone operates in a PBX system. If the telephone still does not work, contact Doro or the place of purchase. Don’t forget the receipt or copy of the invoice will be required for guarantee purposes.
  • Page 13 9AM - 5PM Monday-Friday excluding Bank Holidays. Alternatively, E-mail on: tech@doro-uk.com You can contact us in writing: Consumer Support Group, Doro UK Ltd., 22 Walkers Road, North Moons Moat, Redditch, Worcestershire, B98 9HE, (regarding any Spares or Technical query), or Telephoning (Spares only): 01527 584377 Web site: www.doro-uk.com...
  • Page 14: Australia And New Zealand

    (As a matter of precaution, we recommend disconnecting the telephone during a thunderstorm). This guarantee does not affect your statutory rights. AUSTRALIA NEW ZEALAND DORO Australia Pty Ltd Atlas Gentech (NZ) Limited PO Box 6760 Private Bag 14927 Baulkham Hills BC NSW 2153...
  • Page 15: Technical Information

    If a charge for local calls is unacceptable, the “DIAL“ button should NOT be used for local calls. Only the 7 digits of the local number should be dialled from your telephone. DO NOT dial the area code digit or the “0“ prefix. www.doro.com...
  • Page 20 English Version 1.1...

Table of Contents