Generac 2,400 PSI Pressure Washer TABLE OF CONTENTS WARNING Safety Rules........2-3 Gasoline and its vapors are extremely Know Your Pressure Washer .
Page 3
Generac 2,400 PSI Pressure Washer WARNING WARNING The high pressure spray could also cause you to Starter and other rotating parts can entangle fall if you are too close to the cleaning surface. hands, hair, clothing, or accessories. Pressure in a running washer builds as you climb.
Generac 2,400 PSI Pressure Washer KNOW YOUR PRESSURE WASHER Read this owner’s manual and safety rules before operating your high pressure washer. Compare the illustrations with your high pressure washer to familiarize yourself with the location of the controls. Save this manual for future reference.
Generac 2,400 PSI Pressure Washer IMPORTANT: Read entire owner’s manual before you Perform these tasks to prepare unit: attempt to assemble or operate your new pressure washer. • Attach the handle to the main unit. • Add oil to the engine. REMOVE PRESSURE •...
Generac 2,400 PSI Pressure Washer Attach Spring Clips to Handle • Use clean, fresh, unleaded fuel and store in approved, clean, covered containers. Use clean fill funnels. Never • Attach spring clips to the left side (viewing from the rear use “stale”...
Generac 2,400 PSI Pressure Washer • Attach the other end of the high pressure hose to the CAUTION! There MUST be at least ten feet of high pressure outlet on the pump (Figure 5). Tighten by unrestricted garden hose between the pressure washer hand.
Generac 2,400 PSI Pressure Washer HOW TO USE YOUR • Pull the Choke rod to the CLOSED position (all the way out, Figure 9). PRESSURE WASHER Figure 9 — Choke Positions Choke Rod If you have any problems operating your pressure washer, please call the pressure washer helpline at 1-800-270-1408.
Generac 2,400 PSI Pressure Washer How to Stop Pressure Washer Follow these instructions to change nozzles: • Engage the safety latch on the spray gun. • Move Throttle Control lever to the “Slow” position. • Pull back the collar on the quick–connect at the end of •...
Generac 2,400 PSI Pressure Washer IMPORTANT: Use soaps designed specifically for After you have applied detergent, scour the surface pressure washers. Household detergents could damage and rinse it clean as follows: the pump. • Apply safety latch to spray gun. •...
Generac 2,400 PSI Pressure Washer GENERAL MAINTENANCE WARNING! Water spraying from a leak is capable of injecting material into skin. Inspect hose RECOMMENDATIONS each time before using it. Never repair a high pressure hose. Replace it with another hose that The pressure washer warranty does not cover items that exceeds the maximum pressure rating of your have been subjected to operator abuse or negligence.
Generac 2,400 PSI Pressure Washer Detach spray gun from high pressure hose. Detach Nozzle Maintenance nozzle extension from spray gun and remove o-ring A pulsing sensation felt while squeezing the spray gun and screen from nozzle extension. Flush the screen, trigger may be caused by excessive pump pressure.
Generac 2,400 PSI Pressure Washer O–Ring Maintenance Empty the pump of liquids by pulling the engine recoil handle about 6 times. This should remove most of the Through the normal operation of your pressure washer, liquid in the pump. o–rings, which keep the connections of the hoses and spray Use Generac brand pump saver to prevent corrosion gun tight and leak–free, may become worn or damaged.
Generac 2,400 PSI Pressure Washer TROUBLESHOOTING Problem Cause Correction Low pressure nozzle (black) is being Replace with any of the three high used. pressure nozzles. Water inlet is blocked. Clear inlet. Inadequate water supply. Provide adequate water flow. Pump has following Inlet hose is kinked or leaking.
LIMITED WARRANTY "Generac Portable Products, LLC will repair or replace, free of charge, any part, or parts of the equipment that are defective in material or workmanship or both. Transportation charges on parts submitted for repair or replacement under this Warranty must be borne by purchaser.
Need help?
Do you have a question about the 2400PSI and is the answer not in the manual?
Questions and answers