Goodman CPG SERIES Installation Instructions Manual page 11

The rating plate is stamped with the model number, type of
gas and gas input rating. Make sure the unit is equipped to
operate on the type of gas available. The gas line installation
must comply with local codes, or in the absence of local codes,
with the latest edition of the National Fuel Gas Code NFPA
54/ANSI Z223.1.
Natural Gas Connection
Natural Gas Capacity of Pipe
in Cubic Feet of Gas Per Hour (CFH)
Nominal Black Pipe Size (inches)
Length of
Pipe in Feet
1/2
10 132
20 92
30 73
40 63
50 56
60 50
70 46
80 43
90 40
100 38
Pressure = .50 PSIG or less and Pressure Drop of 0.3" W.C. (Based
on 0.60 Specific Gravity Gas)
BT UH Furnace Input
C FH =
H eating Value of G as (BTU/Cubic Foot)
Refer to the Proper Piping Practice drawing for the general
layout at the unit. The following rules apply:
1. Use black iron pipe and fittings for the supply piping.
The use of a flex connector and/or copper piping is
permitted as long as it is in agreement with local
codes.
2. Use pipe joint compound on male threads only. Pipe
joint compound must be resistant to the action of the
fuel used.
3. Use ground joint unions.
4. Install a drip leg to trap dirt and moisture before it can
enter the gas valve. The drip leg must be a minimum
of three inches long.
5. Use two pipe wrenches when making connection to
the gas valve to keep it from turning.
6. Install a manual shut-off valve in a convenient location
(within six feet of unit) between the meter and the
unit.
7. Tighten all joints securely.
8. The unit must be connected to the building piping by
one of the following methods:
• Rigid metallic pipe and fittings
• Semirigid metallic tubing and metallic fittings
(Aluminum alloy tubing must not be used in exterior
locations)
• Listed gas appliance connectors used in accordance
with the terms of their listing that are completely in
the same room as the equipment
• In the prior two methods above the connector or
tubing must be protected from physical and thermal
damage. Aluminum alloy tubing and connectors must
be coated to protect against external corrosion when
in contact with masonry, plaster or insulation or are
subject to repeated wettings by liquids (water - not
rain water, detergents or sewage).
1
3/4 1 1/4 1 1/2
278 520 1050 1600
190 350 730 1100
152 285 590 980
130 245 500 760
115 215 440 670
105 195 400 610
96 180 370 560
90 170 350 530
84 160 320 490
79 150 305 460
DOOR
PROVIDE CLEARANCE
FOR REMOVAL OF
ACCESS PANELS
MANUAL
SHUTOFF VALVE
PROPER PIPING PRACTICE
NOTE: The unit gas supply entrance is factory sealed with
plugs. Keep plugs in place until gas supply is ready to be
installed. Once ready, replace the plugs with the supplied
grommets and install gas supply line.
G P C
AS IPING HECKS
T
O PREVENT PROPERTY DAMAGE
THE FOLLOWING INSTRUCTIONS
CONNECTIONS AND PRESSURE
• T
HE UNIT AND ITS GAS
BEFORE PLACING IN OPERATION
,
EXPLOSION OR FIRE NEVER
. N
FOR LEAKS EVER EXCEED
H
IGHER PRESSURE MAY
OVERFIRING WHICH MAY
.
FAILURE
• T
HIS UNIT AND ITS SHUT
THE GAS SUPPLY DURING
AT TEST PRESSURES IN
• T
HIS UNIT MUST BE ISOLATED
CLOSING ITS MANUAL
TESTING OF THE GAS SUPPLY
EQUAL TO OR LESS THAN
T
O AVOID PROPERTY DAMAGE
NO OPEN FLAME IN THE VICINITY
There will be air in the gas supply line after testing for leaks
on a new installation. Therefore, the air must be bled from
the line by loosening the ground joint union until pure gas is
expelled. Tighten union and wait for five minutes until all gas
has been dissipated in the air. Be certain there is no open
flame in the vicinity during air bleeding procedure. The unit is
placed in operation by closing the main electrical disconnect
switch for the unit.
11
GROUND JOINT
UNION
CAUTION
OR PERSONAL INJURY DUE
MUST BE PERFORMED REGARDING
:
TESTING
CONNECTIONS MUST BE LEAK
. B
ECAUSE OF THE DANGER
USE A MATCH OR OPEN FLAME
SPECIFIED PRESSURES FOR
DAMAGE GAS VALVE AND CAUSE
RESULT IN PREMATURE HEAT
‐
OFF VALVE MUST BE DISCONNECTED
ANY PRESSURE TESTING OF
1/2 PSIG (3.48
EXCESS OF K
FROM THE GAS SUPPLY
‐
SHUT OFF VALVE DURING ANY
PIPING SYSTEM AT TEST
1/2 PSIG (3.48 P ).
K A
WARNING
,
OR PERSONAL INJURY BE
.
DURING AIR BLEEDING
DRIP LEG
,
TO FIRE
GAS
TESTED
OF
TO TEST
.
TESTING
EXCHANGE
FROM
THAT SYSTEM
P ).
A
SYSTEM BY
PRESSURE
PRESSURES
SURE THERE IS