Advertisement
Advertisement
Table of Contents
Related Manuals for Ryobi EDP2521L
Summary of Contents for Ryobi EDP2521L
- Page 1 EDP2521L DRILL PRESS OWNERʼS OPERATION MANUAL N197...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Table of Contents Specificatons Rules for Safe Operation Unpacking Loose Parts List Assembly Adjustment Operation 9-10 Maintenance Troubleshooting PRODUCT SPECIFICATIONS Input 250 watt No Load Speed 625 - 2500 R.P.M. Drilling Capacity 13 mm Chuck Capacity 13 mm Spindle Taper Spindle Travel 50 mm... -
Page 3: Rules For Safe Operation
RULES FOR SAFE OPERATION Safe operation of this power tool requires that you injury. Nonslip footwear is recommended when read and understand this operator’s manual and all working outdoors. Wear protective hair covering labels affixed to the tool. Safety is a combination to contain long hair. - Page 4 WARNING: other reproductive harm. Some examples of these chemicals are: When servicing use only identical Ryobi replacement . lead from lead-based paints. parts. Use of any other parts may create a hazard . crystalline silica from bricks and cement and other or cause product damage.
- Page 5 For service we suggest you return the instructions, safety rules, etc. contained in this tool to your nearest RYOBI AUTHORISED SERVICE manual. Failure to comply can result in accidents for repair. When servicing,use only identical CENTRE involving fire, electric shock, or serious personal Ryobi replacement parts.
-
Page 6: Rules For Safe Operation
Bright shiny reflective sheet steel or the like is not suitable for laser use as the reflective surface could direct the beam back at the operator. Do not change the laser light assembly with a different type. Repairs must be carried out by authorised Ryobi service centre. Page 5... -
Page 7: Unpacking
Lift the tool from the carton and place it on a level work surface. Contact your nearest Ryobi dealer for assistance if an parts are missing or damage. Do not discard the packing materials until you have carefully inspected the machine, identified all loose parts, and satifactorily operated your tool. -
Page 8: Assembly
ASSEMBLY On/Off Switch Laser Switch Drill Chuck Feeding Handles Column Table Table Height Adjustment Clamping Lever Base Fig.1 ASSEMBLE THE COLUMN INSTALL THE FEEDING HANDLES Place column assembly on base and align Screw the knobs to the feeding handles. holes in column support with holes in base. Screw each feeding handle into hub of pinion shaft. -
Page 9: Adjustment
ADJUSTMENT TABLE ADJUSTMENT DEPTH ADJUSTMENT Height Adjustment (Fig 2) Feed depth Adjustment (Fig 5) To adjust up or down , loosen the clamping lever, then Lower spindle assembly to desired depth and spin down adjust the table to the desired position and re-tighten nut. -
Page 10: Operation
ADJUSTMENT The proper drill speed for a given drill bit size is INSTALLING DRILL BITS as follows: Open chuck jaws with chuck key (Fig 8) Insert drill bit into chuck jaws approx. 25mm. When using STEEL CAST DRILL METAL ALUMINIUM PLASTIC WOOD IRON a small drill bit, do not insert it so far that the jaws touch (mm) -
Page 11: Maintenance
OPERATION Change batteries: The laser beam should be aligned before being used for the first time. Turn off the drill press and switch off the laser beam. Turn on the laser. Open the battery cover of the laser beam on/off Mark a cross as the target location to be drilled switch. -
Page 12: Troubleshooting
TROUBLESHOOTING TROUBLE POSSIBLE CORRECTIVE ACTION A) Adjust tension Noisy Operation A) Incorrect belt tension B) Remove spindle/quill assembly lubricate B) Dry spindle C) Lighten pulley C) Loose pulley D) Replace bearing D) Bad bearing A) Tighten by pressing chuck down on table Excessive Drill Wobble A) Loose chuck B) Replace spindle shaft or bearing... - Page 13 NOTE Page 12...
- Page 14 RYOBI NEW ZEALAND PTY. LTD. AUCKLAND: 27 Clemow Drive, Mt Wellington, N.Z. Tel: (09) 573 0230 - Free Call: 0800 279 624 - Fax: (09) 573 0231 - www.ryobi.co.nz Contact during normal business hours. This Guarantee Form Should Be Retained By The Customer At All Times For your record and to assist in establishing date of purchase (necessary for in-guarantee service) please keep your purchase docket and this form completed with the following particulars.
Need help?
Do you have a question about the EDP2521L and is the answer not in the manual?
Questions and answers