Download Print this page

AEG 24968GM Use, Installation And Maintenance Instructions

Built-in.
Hide thumbs

Advertisement

USE, INSTALLATION AND
MAINTENANCE INSTRUCTIONS
FOR BUILT-IN HOT PLATES
Dear User,
We are sincerely grateful to you for purchasing one of our products. This
appliance has been designed to meet all the modern requirements and is
manufactured from the finest materials and components.
We would ask you to read the instructions within this booklet very carefully so
as to enable you to obtain quality results from the outset.
The design of the figures contained in this handbook is purely indicative.
THE APPLIANCE MUST BE INSTALLED ONLY BY AUTHORISED
PERSONNEL IN COMPLIANCE WITH THE INSTRUCTIONS PROVIDED.
THE MANUFACTUTER DECLINES ALL RESPONSIBILITY FOR IMPROPER
INSTALLATION WHICH MAY HARM PERSONS AND ANIMALS AND
DAMAGE PROPERTY.
THE APPLIANCE MUST BE USED FOR THE PURPOSE FOR WHICH IT
WAS EXPRESSLY DESIGNED. ANY OTHER USE (e.g. HEATING ROOMS)
IS CONSIDERED TO BE IMPROPER AND CONSEQUENTLY DANGEROUS.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE
RESULTING FROM IMPROPER AND IRRESPONSIBLE USE.
The manufacturer is not responsible for any transcription errors or misprints contained in this handbook and,
furthermore, reserves the right to make any modification on the products, which might be deemed necessary
or useful, this being also in the user's interest, without altering their basic operating or safety features.
COD. 115800AEG680 - 03.10.2003

Advertisement

   Related Manuals for AEG 24968GM

   Summary of Contents for AEG 24968GM

  • Page 1: Maintenance Instructions

    USE, INSTALLATION AND MAINTENANCE INSTRUCTIONS FOR BUILT-IN HOT PLATES Dear User, We are sincerely grateful to you for purchasing one of our products. This appliance has been designed to meet all the modern requirements and is manufactured from the finest materials and components. We would ask you to read the instructions within this booklet very carefully so as to enable you to obtain quality results from the outset.

  • Page 2

    DESCRIPTION OF THE HOT PLATES 24658 G-m 24968 G-m 1) Large burner (Left front) of 11.2 MJ (3100 W) 2) Medium burner (Right rear) of 10.2 MJ (2950 W) 3) Small burner (Left rear) 4.9 MJ (1450 W) 4) Auxiliar burner (Right front) 4.0 MJ (1050 W) 5) Fish burner (Center)

  • Page 3

    1) BURNERS HOW TO USE THE BURNER HOTPLATES In order to maximize the efficiency of the burners Ensure that all gas supply connections are correct the following pan sizes are recommended: and that supply valves are open. The burner controls are engraved graphically to BURNER PAN DIAMETER indicate their associated burner and setting.

  • Page 4

    - DO NOT SPRAY AEROSOLS IN THE VICINITY are no mentions on the instruction book) the OF THE HOTPLATES WHILE THE APPLIANCE user must apply to the servicing “AEG” IS IN USE. imparting both the “ENR” and “FNR” numbers - FOR SAFETY ENSURE THAT NO FLAMMABLE...

  • Page 5

    CLEANING WARNING: 4) PARTS IN STAINLESS STEEL Do not wash any part while it is still hot. Parts in stainless steel must be cleaned with warm soapy water and dried with a clean soft cloth. 2) HOTPLATE Frequent use of cleaning agents designed for Periodically, the enamelled trivets, burners and stainless steel is recommended.

  • Page 6

    INSTALLATION TECHNICAL INFORMATION FOR THE CHILDREN SINCE THEY ARE A SOURCE OF POTENTIAL DANGER. INSTALLATION PERSONNEL 6) FIXING OF THE HOTPLATE WARNING: The hotplate is provided with a special seal to This appliance must be installed only by prevent liquid penetrating to the underside of the authorised personnel and in accordance with appliance.

  • Page 7

    INSTALLATION 7) GAS CONNECTION 8) ELECTRICAL CONNECTION The gas connection is located at the rear and on the The appliance is supplied with a 1800 mm long underside of the appliance 100 mm from the right flexible supply lead. hand side. The point of attachment for this lead is located at Natural Gas the rear and on the underside of the appliance 380...

  • Page 8

    REGULATION Warning: 10) CONTROL VALVES Adjustment of this appliance shall only be “Reduced rate” adjustment carried out only by authorised personnel. The control valves are suitable for all types of gases. They are the male cone type allowing one direction 9) BURNERS of flow.

  • Page 9

    CONVERSIONS Warning: figure 22). Conversion of this appliance shall only be - Unscrew the injector with the open ended spanner carried out only by authorised personnel. until there is clearance for the spring hook “P”, to engage the injector. 11) REPLACEMENT OF INJECTORS - Unscrew the injector completely.

  • Page 10

    MAINTENANCE Warning: and secure the screws (refer figure 25). Maintenance, service and repairs of this appliance shall only be carried out only by Replacement of electric cable authorised personnel. - Should the flexible supply lead need replacement it is essential that one of the correct rating and 12) REPLACEMENT OF COMPONENTS construction be used.

  • Page 11

    FIG. 29 FIG. 30 HOT PLATES TECHNICAL DATA PRESSURE 3 + 1 WOK BURNERS 4 BURNERS 3 + 1 WOK BURNERS (NO WOK) “RECTANGULAR” “RECTANGULAR” “SOFT” 24658 G-m PROPANE 2.75 kPa 2.75 kPa 2.75 kPa NATURAL 1.00 kPa 1.00 kPa 1.00 kPa TOT.

  • Page 12

    ANDI-CO AUSTRALIA PTY LTD ABN 68 005 899 365 For Service Phone: 1300 650 020 (in Australia) Spare Parts Tel: (03) 9569 7744 www.andico.com.au Melbourne Head Office: 1 Stamford Road, OAKLEIGH VIC 3166 Tel: (03) 9569 1255, Fax: (03) 9569 1450 Sydney Office: 97 Rose Street, CHIPPENDALE NSW 2008 Tel: (02) 9380 8444...

Comments to this Manuals

Symbols: 0
Latest comments: