Related Manuals for GMC PFC46V
Summary of Contents for GMC PFC46V
- Page 1 4.2V QUICK CHARGE CORDLESS SCREWDRIVER PFC46V INSTRUCTION MANUAL Black Magenta Code: PFC42V Cyan Yellow Date: 080122 Edition: 5 Op: DCR...
-
Page 2: Table Of Contents
Contents Warranty Introduction Environmental protection Description of symbols Specifications Safety instructions Additional safety instructions for cordless screwdrivers Additional safety instructions for the charger When to charge the tool Know your product Unpacking Important information – special product care Charging To obtain the best life for the tool Using the screwdriver Maintenance Warranty Power Tools... -
Page 3: Introduction
Introduction Your new GMC power tool will more than satisfy your expectations. It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria. You will find your new tool easy and safe to operate, and, with proper care, it will give you many years of dependable service. -
Page 4: Safety Instructions
Safety instructions WARNING. Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/ or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery or capacitor operated (cordless) power tool. -
Page 5: Additional Safety Instructions For Cordless Screwdrivers
c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. -
Page 6: Additional Safety Instructions For The Charger
• Rags, cloths, cord, string and the like should never be left around the work area. • Support the work properly. • If you are interrupted when operating, complete the process and switch off before looking up. • Periodically check that all nuts, bolts and other fixings are properly tightened. - Page 7 • Do not use the charger if it has been subjected to a heavy knock, dropped or otherwise damaged in anyway. Take the charger to an authorised service centre for a check or repair. • Do not disassemble the charger. Phone and speak with an experienced GMC Customer Service Representative or contact an Authorised Service centre for assistance.
-
Page 8: When To Charge The Tool
When to charge the tool • New tools are shipped in a low charge condition and must be fully charged before use. It takes approximately 45 seconds to fully charge the tool. • Charging the tool should not be undertaken casually. Through the charging cycle monitor the tool and make sure that screwdriver is charging. -
Page 9: Know Your Product
Know your product This screw driver is for light to medium applications of screws and small nuts and bolts. If the screw driver is unable to rotate the fastener do not over load by holding the switch in the on position and manually rotating the fastener. -
Page 10: Unpacking
Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. -
Page 11: To Obtain The Best Life For The Tool
To obtain the best life for the tool The screwdriver should be placed on charge when ever the tool no longer can perform tasks previously achieved. Do Not completely run down the charge. DO NOT continue to use the screwdriver when the charge is exhausted. The screwdriver does not have automatic spindle lock and using the screwdriver with no charge may damage the tool. -
Page 12: Maintenance
Inserting and removing bits 1. Select an appropriate bit and Insert it into the hexagonal hole in the chuck/bit retainer (1). The screwdriver is now ready for use. 2. To remove the screwdriver bit you simply remove the existing bit by pulling the bit out of the chuck/bit retainer (1). - Page 16 GMC customer assist If your product needs repairing, replacing, technical service or you simply need help or advice, please contact us on our Customer Assist Line 1300 880 001 (Australia) or 0800 445 721 (New Zealand). For prompt service we suggest you log your service request online at www.gmcservice.com.au.