Advertisement
Table of Contents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tysso BT series
Summary of Contents for Tysso BT series
- Page 1 User's Manual Bluetooth Scanners BT Series...
-
Page 2: Table Of Contents
Contents 1. Introduction ............2. Available models ..........3. Standard package ..........4. Recharge............5. Installation (Receiver) ........6. Three operational modes........7. Scanner programming........8. Purge scanned data from scanner...... 13 (recapture mode only) 9. Audible & Visual Indicators and Operation..14... -
Page 3: Introduction
Reader's external power adapter (option) Furthermore, user friendly operation and large memory · RS-232 interface receiver comes with PS/2 retrieving capacity characteristics give BT series a jump on its clone. · power cable (default) RS-232 interface receiver external power adapter ·... -
Page 4: Recharge
5. Installation (Receiver): Just plug in the USB retrieving power cable or reader's BT series' paring between scanner and receiver is made external power adapter to DC jack of the scanner, as before shipment. So, normal operation can be started after drawings show, and push &... - Page 5 5.2. BT-XXXX-R: RS-232 interface 5.2.1. Using PS/2 retrieving power cable (default) 5.2.2. Using external power adapter (option) Turn off the host computer. Turn off the host computer. · · Connect the D-type 9-pin cable connector of the Connect the D-type 9-pin cable connector of the ·...
-
Page 6: Three Operational Modes
6. Three operational modes: 5.3. BT-XXXX-U: USB interface 6.1. Batch mode (default): Turn off the host computer. Scanner transmits scanned barcode data right after · Connect the USB A type connector on the receiver into scanning barcode label to receiver or scanner stores ·... -
Page 7: Scanner Programming
7. Scanner programming: Note: There is no feedback protocol between host The BT series can be configured via the Windows base computer and receiver no matter what which programming utility to meet special application needs interface equipped. The radio link between the such as decoding options, code ID settings, etc. -
Page 8: Purge Scanned Data From Scanner
8. Purge scanned data from scanner: (recapture mode only) Note: Step 1. Run the attached CD disk:\utilities\BTScanner. There are two folders in the BTScanner Utility, one is · Step 2. If the receiver is keyboard wedge interface, please BTScanner and another is KBIDrv. install KBIDrv (interface driver) and follow by BT folder is the scanner programming utility and ·... -
Page 9: Audible & Visual Indicators And Operation
9. Audible & Visual Indicators and Operation: Operation: By plugging USB retrieving power cable or external power adapter cable into 9.1. Audible indicators (Scanner) scanner's DC jack. No response Bluetooth radio link status by pushing and holding · trigger Indications: Indicates the Bluetooth radio link set to off. Operation: By disconnecting USB retrieving power 5-ascending tone beep cable or external power adapter cable from... - Page 10 · 2 beeps before scanner emits the red light KB, the memory full status starts warning. BT series offer 192KB memory for keeping data. · Indications: Indicates the scanner is at low power state. It is roughly stored EAN 13 barcode up to 15,000 Operation: Operate scanner to read a barcode.
- Page 11 9.2. Visual indicators · Bluetooth radio link status (scanner) ·Bluetooth radio link status (receiver) Red LED off Red LED flash Indications: Indicates the scanner is at Bluetooth radio Indications: Indicates Bluetooth radio link with scanner link off state. break (it's possibly caused by poor Operation: To enable Bluetooth radio link on state, communication quality or radio link is set by pushing and holding the trigger over 5...
- Page 12 Green LED On Programming to be done successfully (scanner) · Green LED on then Red LED on Indications: Indicates the scanner (battery) is at full charged state. Operation: It takes about 4 hours to complete the Indications: Indicates programming to be done charging process.
Need help?
Do you have a question about the BT series and is the answer not in the manual?
Questions and answers